Extron electronic 68-388-01 manual Select format for VID1 and/or VID2

Page 21

Chapter 3 • Operating the System 5cr

Select format for VID1 and/or VID2.

To set these two inputs for either Composite or S-video, in Config Mode, do the following:

1b. Press and hold the Room button until finished with this operation. After 2 seconds, one of the VID1 LEDs lights.

2b. Press VID1 to toggle between VID (Video) and Y/C (S-video) formats.

3b. Repeat step 2b to select the format to set the format for the VID2 input.

4b. Release the Room button to go back to Config mode.

5b. While in Config mode, you may go directly to another procedure, wait for 20 second time-out or press all 3 Display buttons for 2 seconds to exit.

Figure 3-2c. Select input format for VID1 and VID2.

Learn Infrared Signals from other devices’ remote controls

This procedure is only necessary if the IR driver is not available for the system projector, or is not complete. A flow chart of the learning procedure is shown in Figure 3-2d and a table of LED codes is shown in Figure 3-2e. In Setup Mode, do this:

1c. Press the panel button to be programmed and hold it for 2 seconds. The Config LED blinks.

2c. Point the IR remote source at the System 5 IR Remote window and press the button briefly, but firmly, for the signal to be “learned”.

Figure 3-2d. Learn infrared signals from other remotes.

_______ It may be necessary to hold remote as near as 1/2 inch and point it

directly into the IR window. It may also help to block out ambient light, such as from fluorescent sources.

The Config LED remains On while TX & Retry LEDs flash to indicate that the operation is complete. (If Retry blinks once and TX - Off, repeat this step). See LED codes in Figure 3-2e below.

_______ The Display Power button learns 2 signals. After learning the 1st signal

(e.g. Power On), the Config and Retry LEDs blink to indicate that it is ready to learn the second signal (Power Off). Double-click the Power button and repeat step 2c to learn the second signal.

3c. Repeat steps 1c and 2c to program the next button.

4c. While in Config mode, you may go directly to another procedure, wait for 20 second time-out or hold all 3 Display buttons for 2 seconds to exit.

________ Once the display device (projector) has been programmed to operate

from the System 5cr, those same control functions should not be done from the projector because the System 5 has no way of knowing what was done at the projector. That is, if the projector was turned on at the System 5 and turned off from the projector panel, the System 5 thinks the projector is still on.

Figure 3-2e. LED response codes

Extron • System 5cr Switcher • User’s Manual

3-4

Page 20 Page 22
Image 21
Page 20 Page 22
Contents System 5cr Precautions Connections Setup Mode proceduresChapter One Introduction to System 5cr Introduction to System 5cr Controlling the System What is a System 5cr Switcher?Infrared Learning for System Control Standard FeaturesInputs OutputsSystem 5 with accessories and options Options and AccessoriesVideo input SpecificationsControl projector Rear Panel Connections Installation in a Rack, on a Wall or Under a Table Panel ConnectionsVideo Input Connections Video Output Connections Audio Input Connections12VDC, 500mA output is provided on the Comm. IR Emitter port Audio Preamp Out Connection Connecting AccessoriesRoom/Relay Connector Comm Connector and Infrared EmitterUsing the System 5cr Using the System 5cr Front Panel Controls and IndicatorsPower and Room 1b. Front panel controls and indicators PC Input Selection Buttons and IndicatorsEnter Setup Config Mode Configuration Setup from the Front PanelClear Configurations Preset Audio Input Attenuation LevelsSelect format for VID1 and/or VID2 Learn Infrared Signals from other devices’ remote controlsRemote Operation See inset top, right To install batteries4Chapter Four Windows Control Software Program Help Installing Windows Control SoftwareExample of two Help screens for the System Program OperationPower Up/Down Delay times Room Relay Mode Latched/MomentaryAuto Set Attenuators set all audio input to the same level Saving a Configuration to a File RGB Delay TimesDownloading from Extron’s IR Projector Library Miscellaneous OptionsLoading Projector Drivers Programming the System 5cr Host-to-System 5cr Instructions Remote Control Port RS-232Ascii Definitions and AbbreviationsAdvanced Instructions Reserved for Windows program BInstalling System 5cr Options System 5cr Options To IR Broadcaster To projector remote jack Following is a list of terms taken from Extron’s Glossary Glossary of termsLCD Index FCC Class a Notice Extron’s Warranty Extron ELECTRONICS, Asia

68-388-01 specifications

Extron Electronics has long been a prominent name in the AV integration industry, known for its innovation and quality products. One of the standout models in their product line is the Extron 68-388-01, a versatile and user-friendly solution designed to enhance various audiovisual experiences. This device exemplifies Extron's commitment to excellence, delivering robust performance and seamless integration for a variety of applications.

The Extron 68-388-01 is primarily an HDMI to RGB scaler designed for converting HDMI signals into high-quality RGB analog video outputs. This feature is particularly beneficial for environments where legacy analog display equipment is still in use, allowing for compatibility with modern HDMI sources without sacrificing signal quality. The device supports a wide range of resolutions up to 1920x1200, ensuring it meets the demands of high-definition content while maintaining clarity and detail.

A key feature of the 68-388-01 is its advanced scaling technology. Utilizing precise scaling algorithms, this device effectively adjusts the input signal to match the native resolution of the output display, minimizing artifacts and enhancing image quality. This technology is particularly useful in settings such as classrooms and conference rooms, where visual clarity is essential for effective communication.

Another notable characteristic of the Extron 68-388-01 is its user-friendly interface. Equipped with a straightforward front-panel control system, users can easily manage settings and configurations, making it suitable for both tech-savvy users and those less familiar with AV technology. Additionally, the device comes with Extron's proprietary software, allowing for remote management and configuration via a connected PC or network.

The build quality of the 68-388-01 is typical of Extron's reputation for durability and reliability. Designed for rack mounting, it fits seamlessly into existing AV installations while offering excellent thermal management and low power consumption. Its compact form factor enhances versatility, making it an ideal choice for a range of environments, from education to corporate and broadcast applications.

In conclusion, the Extron 68-388-01 stands out as an exceptional HDMI to RGB scaler, combining advanced features, robust performance, and ease of use. Its ability to bridge the gap between modern digital sources and legacy analog displays makes it an invaluable tool for any AV professional looking to create a flexible and future-proof installation.
Top Page Image Contents