Extron electronic SCP 150L user manual Installation and Operation, cont’d, UL Requirements

Page 7

Installation and Operation, cont’d

To mount the SCP 150 in areas of walls or furniture without studs, use an optional Extron 2-gang mounting bracket, part #70-086-01, -11, or -21. For the SCP 150 AAP, use an Extron 4-gang mounting bracket, part #70-086-03, -13, or -23.

To mount the SCP 150 externally on a wall or desktop, use an optional Extron 2-gang SMB surface mount box, part #60-640-02. For the SCP 150 AAP, use an Extron 4-gang SMB, part #60-642-02.

UL Requirements

The Underwriters Laboratories (UL) requirements listed below pertain to the installation of the SCP into a wall or furniture.

Installing the Electrical Box

If you are using a mounting bracket or SMB instead of an electrical box, follow the mounting instructions that came with the bracket or SMB.

To install the electrical box:

1.Insert the electrical box into the opening, and attach the wall box to the wall stud (2" x 4") or furniture with nails or screws, leaving the front edge flush with the surface, as shown in the following illustration.

1.This unit is not to be connected to a centralized DC power source or used beyond its rated voltage range.

2.This unit must be installed in a UL listed electrical wall box.

The UL approved electrical box is not included with the SCP; the installer is responsible for obtaining and installing the box.

3.This unit must be installed in accordance with the National Electrical Code.

Preparing the Site

To mount the panel using either an electrical box or a mounting bracket, use one of the rough-in templates provided on pages A-7 through A-9 as a guide to measure and mark the hole in the

Wall Stud

Wall Box

Screws or Nails

Flush with Wall Surface

wall or furniture through which the SCP will be mounted. The templates provide measurements for installing the panel with either an electrical box or a mounting bracket. You do not need the template if you are mounting the panel using an SMB.

The templates are not to scale and are provided for reference only.

To prepare the site:

1.Choose a mounting location. If using an electrical box to wall-mount the panel, locate a stud to which the box will be attached.

2.Use the appropriate template and panel dimensions in Appendix A to as a guide to measure and mark the area to cut out of the wall or furniture.

3.Cut out the opening in the wall or furniture.

To attach the wall box to wood, use four #8 to #10 wood or sheet metal screws. A minimum of 1/2 inch (1.25 cm) of screw threads must penetrate the wood. If the wood is a 2 x 4, such as a wall stud, 10-penny or larger nails can be used.

To attach the electrical wall box to metal, use four #8 or #10 sheet metal screws (self-tapping) or #8 or #10 machine bolts with matching nuts.

2.Feed the cables into the wall box. Cable clamps should be used to hold the cables in place for strain relief.

3.Exposed cable shields (braids or foil) are potential sources of short circuits. Trim back and/or insulate shields with heat shrink.

2-4

SCP 150 • Installation and Operation

SCP 150 • Installation and Operation

2-5

Image 7
Contents User’s Manual Secondary Control Panels for the System 5 IP SwitcherExtron’s Warranty PrecautionsTable of Contents SCP Table of Contents, cont’dIi SCP 150 Table of Contents IntroductionSCP Installation and OperationFeatures IntroductionSCP 150 Installation and Operation Installation and OperationInstallation Overview Installing or Replacing Button LabelsPreparing the Site Installation and Operation, cont’dInstalling the Electrical Box UL RequirementsIRCM-DV+ Installation and Operation, cont’d Cabling the Rear PanelMounting on a lectern Mounting the SCPMounting in a wall box Mounting in a rackSCP 150 L Installation and Operation, cont’d Front Panel FeaturesResetting the SCP 150 to factory defaults Resetting to Factory Firmware versionExtron Remote CommunicationRemote Communication Setting Up RS-232 CommunicationUsing Simple Instruction Set SIS Commands Using the command/response tablesRemote Communication, cont’d Command/response table for SIS commandsReset to default settings Zap Special Function SIS CommandsVolume relative function CommandCommand Ascii Command Response Values Command/response table for special function SIS commands150 Switch number locations Switch Function ButtonRemote Communication, cont’d Updating Firmware AAppendix a Specifications, Part Numbers, Accessories, and DimensionsIncluded Parts Control/remote control padGeneral Cables AccessoriesPanel Dimensions Accessories Part numberTemplates SCP 150 Specifications, Parts, Accessories, Dimensions A-7SCP 150 L SCP 150 L SCP 150 Specifications, Parts, Accessories, Dimensions A-9

SCP 150L specifications

The Extron Electronics SCP 150L is a versatile and sophisticated control processor designed to streamline AV system management in a variety of environments, including classrooms, conference rooms, and auditoriums. With a focus on ease of use and reliable performance, the SCP 150L represents an integral part of modern AV control solutions.

One of the key features of the SCP 150L is its powerful processing capability. This control processor supports a variety of interfaces and communication protocols, making it easy to integrate with existing AV systems. It is equipped with support for both serial and Ethernet communication, allowing it to control a wide range of devices, including projectors, displays, and audio systems. The SCP 150L can also manage third-party devices, providing users with expanded control options.

Another significant characteristic of the SCP 150L is its user-friendly interface. The device features an intuitive web-based interface, enabling users to configure settings, monitor system status, and execute commands from any device with a web browser. This simplicity in design ensures that users can quickly familiarize themselves with the system, reducing the learning curve associated with more complex control environments.

The SCP 150L is also designed with flexibility in mind. It supports customizable control options, allowing for tailored control schemes that can cater to specific user needs and preferences. This adaptability makes it an ideal choice for environments where AV system requirements may frequently change.

Furthermore, the SCP 150L includes support for Extron’s GlobalViewer Enterprise, which facilitates remote monitoring and management of AV systems. This feature enhances operational efficiency by allowing users to diagnose issues remotely and receive alerts, ultimately minimizing downtime and optimizing system performance.

The compact design of the SCP 150L is another notable characteristic, making it suitable for installation in a variety of settings without occupying excessive space. Its robustness ensures durability, providing users with a reliable solution that can withstand the demands of daily AV operations.

In summary, the Extron SCP 150L is a key component in effective AV system management. Its powerful processing capabilities, user-friendly interface, flexibility, and remote management support make it a standout choice for anyone seeking to enhance the functionality of their AV systems while ensuring maximum ease of use. With the SCP 150L, users can achieve a streamlined and efficient control experience that meets the dynamic needs of modern AV environments.