Extron electronic SCP 150L Installation and Operation, cont’d Cabling the Rear Panel, Ircm-Dv+

Page 8

Installation and Operation, cont’d

Cabling the Rear Panel

3Serial/host port — Use this 3-pole captive screw connector to connect to your PC’s RS-232 port. Extron Simple Instruction Set (SIS) commands can then be issued from the PC to monitor and obtain information from the SCP. This port is also used for uploading firmware to the SCP, if necessary. Refer to chapter 3, Remote Communication, for further details.

1

4

3

2

1

 

 

ON

J5

2

3

Do not connect to this port if the SCP is being used with the System 5IP.

A B C D E

IR Link

1Panel address DIP switch — If using two SCPs, set DIP switch 1 to assign a unique address to each panel. Set the switch to Off to assign address 00 and On to assign address 01. Switches 2 and 3 are not used.

A +12VDC B Ground ( )

D IR Link

The System 5 IP can support up to two SCPs. The panels must each have a unique address.

DIP switch 4 is used to enable the RS-232/host port of the SCP 150. Note: If the SCP is connected to the System 5IP, set switch 4 to the “off” position.

2CM/IR/SCP connectors — These two 5-pole captive screw connectors function in exactly the same way and can be used interchangeably. Connect one connector to a System 5 IP switcher and the other to a second SCP, an Extron control module (ACM, RCM, IRCM), or an Extron IR Link infrared signal repeater.

Two SCPs, up to four control modules, and one IR Link can be daisy-chained using these connectors. The maximum distance between the System 5 IP and a connected device is 200' (61 m).

The switcher provides 12 VDC power to the SCP and any daisy- chained control devices via these connectors, so no additional power supply is required.

Wire the connectors as shown in the illustration on the next page. The illustration is a guide; the SCPs, control modules, and IR Link can be daisy-chained in combinations other than the one shown.

4

3

2

1

 

 

ON

SCP 150

IRCM-DV+

A B C D E

A B C D E

Control Module

 

 

A

+12VDC

A

B

Ground ( )

B

C Control signal (IRCM)

C

D Modulated IR (IR Link)

D

A

+12VDC

A

B

Ground ( )

B

C

Control signal (IRCM)

C

D Modulated IR (IR Link)

D

E

SCP Communication (IR)

E

J5

System 5 IP

Rear Port

SIGNAL

IR LINK

IR Link

DVD CONTROL

Tx

 

MENU

 

 

TITLE

 

 

ENTER

 

 

REW PLAY

NEXT PAUSE

STOP

Control

 

Module

 

VOLUME

PROJECTOR

 

 

 

SCP 150

SCP 150

2-6

SCP 150 • Installation and Operation

SCP 150 • Installation and Operation

2-7

Image 8
Contents Secondary Control Panels for the System 5 IP Switcher User’s ManualPrecautions Extron’s WarrantyTable of Contents Table of Contents, cont’d Ii SCP 150 Table of ContentsIntroduction SCPInstallation and Operation FeaturesIntroduction SCPInstallation and Operation Installation OverviewInstalling or Replacing Button Labels SCP 150 Installation and OperationInstallation and Operation, cont’d Installing the Electrical BoxUL Requirements Preparing the SiteInstallation and Operation, cont’d Cabling the Rear Panel IRCM-DV+Mounting the SCP Mounting in a wall boxMounting in a rack Mounting on a lecternInstallation and Operation, cont’d Front Panel Features SCP 150 LResetting to Factory Firmware version Resetting the SCP 150 to factory defaultsRemote Communication ExtronSetting Up RS-232 Communication Using Simple Instruction Set SIS CommandsUsing the command/response tables Remote CommunicationCommand/response table for SIS commands Remote Communication, cont’dSpecial Function SIS Commands Volume relative functionCommand Reset to default settings Zap150 Command/response table for special function SIS commandsCommand Ascii Command Response Values Switch Function Button Switch number locationsRemote Communication, cont’d Updating Firmware Specifications, Part Numbers, Accessories, and Dimensions AAppendix aGeneral Control/remote control padIncluded Parts Accessories Panel DimensionsAccessories Part number CablesSCP 150 L SCP 150 Specifications, Parts, Accessories, Dimensions A-7Templates SCP 150 Specifications, Parts, Accessories, Dimensions A-9 SCP 150 L

SCP 150L specifications

The Extron Electronics SCP 150L is a versatile and sophisticated control processor designed to streamline AV system management in a variety of environments, including classrooms, conference rooms, and auditoriums. With a focus on ease of use and reliable performance, the SCP 150L represents an integral part of modern AV control solutions.

One of the key features of the SCP 150L is its powerful processing capability. This control processor supports a variety of interfaces and communication protocols, making it easy to integrate with existing AV systems. It is equipped with support for both serial and Ethernet communication, allowing it to control a wide range of devices, including projectors, displays, and audio systems. The SCP 150L can also manage third-party devices, providing users with expanded control options.

Another significant characteristic of the SCP 150L is its user-friendly interface. The device features an intuitive web-based interface, enabling users to configure settings, monitor system status, and execute commands from any device with a web browser. This simplicity in design ensures that users can quickly familiarize themselves with the system, reducing the learning curve associated with more complex control environments.

The SCP 150L is also designed with flexibility in mind. It supports customizable control options, allowing for tailored control schemes that can cater to specific user needs and preferences. This adaptability makes it an ideal choice for environments where AV system requirements may frequently change.

Furthermore, the SCP 150L includes support for Extron’s GlobalViewer Enterprise, which facilitates remote monitoring and management of AV systems. This feature enhances operational efficiency by allowing users to diagnose issues remotely and receive alerts, ultimately minimizing downtime and optimizing system performance.

The compact design of the SCP 150L is another notable characteristic, making it suitable for installation in a variety of settings without occupying excessive space. Its robustness ensures durability, providing users with a reliable solution that can withstand the demands of daily AV operations.

In summary, the Extron SCP 150L is a key component in effective AV system management. Its powerful processing capabilities, user-friendly interface, flexibility, and remote management support make it a standout choice for anyone seeking to enhance the functionality of their AV systems while ensuring maximum ease of use. With the SCP 150L, users can achieve a streamlined and efficient control experience that meets the dynamic needs of modern AV environments.