Gigabyte GA-K8NE-RH user manual Comb Comb Connector, CI Chassis Intrusion, Case Open

Page 24

English

13)COMB (COMB Connector)

Be careful with the polarity of the COMB connector. Check the pin assignments while you connect the COMB cable. Please contact your nearest dealer for optional COMB cable.

			Pin No.	Definition
			1	NDCDB-
			2	NSINB
	2	10	3	NSOUTB
	2	10	4	NDTRB-
			4	NDTRB-
	1	9	5	GND
	1	9	6	NDSRB-
			6	NDSRB-
			7	NRTSB-
			8	NCTSB-
			9	NRIB-
			10	No Pin

14)CI (Chassis Intrusion, Case Open)

This 2-pin connector allows your system to detect if the chassis cover is removed. You can check the "Case Opened" status in BIOS Setup.

1

Pin No.	Definition
1	Signal
2	GND

GA-K8NE-RH Motherboard

- 24 -

Image 24

Contents

GA-K8NE-RH Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation Item Checklist GA-K8NE-RH Motherboard Layout Block Diagram Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary ALC850 Codec UAJUse of licensed Award Bios Installation of the CPU and Heatsink Installation of the CPUInstallation of Memory Installation of the HeatsinkDDR1 DDR2 DDR3 Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction Side Speaker OutATX12V / ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD Connector IDE1 / IDE2 IDE Connector SATAII01 / SATAII23 Serial ATA ConnectorFpanel Front Panel Jumper Faudio Front Audio Panel Connector PwrledCdin CD In Connector USB1 / FUSB2 / FUSB3 Front USB ConnectorComb Comb Connector CI Chassis Intrusion, Case OpenBAT Battery Clrcmos Clear CmosEnglish Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. FDh F12 For Boot Menu„ Standard Cmos Features „ Advanced Bios Features„ Power Management Setup „ PnP/PCI ConfigurationTime IDE Channel 0 Master, Slave, IDE Channel 1 Master, SlaveIDE Channel 2/3/4/5 Master Floppy 3 Mode Support for Japan Area Drive a / Drive BHalt on Hard Disk Boot Priority First / Second / Third Boot DeviceBoot Up Floppy Seek Password Check Init Display FirstIDE DMA transfer access Integrated PeripheralsOn-Chip IDE Channel0 On-Chip IDE Channel1IDE Prefetch Mode On-Chip MAC LanNV IDE/SATA RAID function NV Serial-ATAParallel Port Mode ECP Mode Use DMAOnboard Parallel Port On-Chip USBPME Event Wake Up Modem Ring OnUSB Resume from Suspend Power-On by Alarm Power On By MousePower On By Keyboard KB Power on FunctionPnP/PCI Configurations PC Health Status DDR25VReset Case Open Status Current CPU TemperatureCPU Warning Temperature Case OpenedTemp of FAN turn off Default temperature 0oC Temp Limit of Low Speed Default temperature 20oCTemp Limit of Mid Speed Default temperature 50oC Temp Limit of High Speed Default temperature 60oCMB Intelligent TweakerM.I.T HT Frequency ratioCPU Frequency DDR clock/Timing Mode RAS# to CAS# delay TrcdRow to Row delay Trrd Write Recovery Time TwrWrite-to-Read Delay Twtr Refresh Rate TrefRead Preamble value Async Latency valueTop Performance Set Supervisor/User Password Save & Exit Setup Exit Without SavingDrivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish Unique Software Utilities EasyTune 5 Introduction User Interface OverviewXpress Recovery2 Introduction How to use the Xpress Recovery2System requirements Main Screen of Xpress Recovery2 PrecautionsLimitations Flash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen EnglishCongratulation!! You have updated Bios successfully Bios file becomes F4 after updatingMethod 2 @BIOSTM Utility Methods and stepsEnglish Serial ATA Bios Setting Utility Introduction RAID LevelsConfiguring the Nvidia RAID Bios Entering the RAID Bios SetupUsing the Define a New Array Window Selecting the RAID ModeSelecting the Striping Block Size Assigning the DisksCompleting the RAID Bios Setup YESArray 2 Nvidia Mirror 76.33G Installing the RAID drivers Cd bootdrv MenuIntroduction of audio connectors Stereo Speakers Connection and Settings5 2- / 4- / 6- / 8- Channel Audio Function Introduction Channel Audio Setup English Step Troubleshooting English English Contact Us Taiwan HeadquartersChina Shanghai