Gigabyte GA-K8NE-RH user manual PnP/PCI Configurations

Page 39

2-5	PnP/PCI Configurations

		CMOS Setup Utility-Copyright (C) 1984-2006 Award Software
			PnP/PCI Configurations
	PCI 1 IRQ Assignment		[Auto]			Item Help
	PCI 2 IRQ Assignment		[Auto]		Menu Level`
	PCI 3 IRQ Assignment		[Auto]
KLJI: Move		Enter: Select	+/-/PU/PD: Value	F10: Save	ESC: Exit	F1: General Help
		F5: Previous Values		F7: Optimized Defaults

	PCI 1 IRQ Assignment
	Auto		Auto assign IRQ to PCI 1. (Default value)
	3,4,5,7,9,10,11,12,14,15		Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 1.
	PCI 2 IRQ Assignment
	Auto		Auto assign IRQ to PCI 2. (Default value)
	3,4,5,7,9,10,11,12,14,15		Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 2.
	PCI 3 IRQ Assignment
	Auto		Auto assign IRQ to PCI 3. (Default value)
	3,4,5,7,9,10,11,12,14,15		Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 3.

English

- 39 -

BIOS Setup

Image 39

Contents

GA-K8NE-RH Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation Item Checklist GA-K8NE-RH Motherboard Layout Block Diagram Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantyALC850 Codec UAJ Feature SummaryUse of licensed Award Bios Installation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of MemoryDDR1 DDR2 DDR3 Installation of Expansion Cards I/O Back Panel Introduction Side Speaker Out Connectors IntroductionATX12V / ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATAII01 / SATAII23 Serial ATA Connector IDE1 / IDE2 IDE ConnectorFpanel Front Panel Jumper Pwrled Faudio Front Audio Panel ConnectorUSB1 / FUSB2 / FUSB3 Front USB Connector Cdin CD In ConnectorCI Chassis Intrusion, Case Open Comb Comb ConnectorClrcmos Clear Cmos BAT BatteryEnglish Main Menu Status Page Setup Menu / Option Page Setup MenuF12 For Boot Menu Main Menu For example Bios Ver. FDh„ PnP/PCI Configuration „ Standard Cmos Features„ Advanced Bios Features „ Power Management SetupTime IDE Channel 0 Master, Slave, IDE Channel 1 Master, SlaveIDE Channel 2/3/4/5 Master Floppy 3 Mode Support for Japan Area Drive a / Drive BHalt on Hard Disk Boot Priority First / Second / Third Boot DeviceBoot Up Floppy Seek Init Display First Password CheckOn-Chip IDE Channel1 IDE DMA transfer accessIntegrated Peripherals On-Chip IDE Channel0 NV Serial-ATA IDE Prefetch Mode On-Chip MAC Lan NV IDE/SATA RAID functionOn-Chip USB Parallel Port ModeECP Mode Use DMA Onboard Parallel PortPME Event Wake Up Modem Ring OnUSB Resume from Suspend KB Power on Function Power-On by AlarmPower On By Mouse Power On By KeyboardPnP/PCI Configurations DDR25V PC Health StatusCase Opened Reset Case Open StatusCurrent CPU Temperature CPU Warning TemperatureTemp Limit of High Speed Default temperature 60oC Temp of FAN turn off Default temperature 0oCTemp Limit of Low Speed Default temperature 20oC Temp Limit of Mid Speed Default temperature 50oCMB Intelligent TweakerM.I.T HT Frequency ratioCPU Frequency Write Recovery Time Twr DDR clock/Timing ModeRAS# to CAS# delay Trcd Row to Row delay TrrdAsync Latency value Write-to-Read Delay TwtrRefresh Rate Tref Read Preamble valueTop Performance Set Supervisor/User Password Exit Without Saving Save & Exit SetupInstall Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish Unique Software Utilities User Interface Overview EasyTune 5 IntroductionXpress Recovery2 Introduction How to use the Xpress Recovery2System requirements Main Screen of Xpress Recovery2 PrecautionsLimitations Flash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Task menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two English Exploring the Q-FlashTMutility screenBios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish RAID Levels Serial ATA Bios Setting Utility IntroductionEntering the RAID Bios Setup Configuring the Nvidia RAID BiosAssigning the Disks Using the Define a New Array WindowSelecting the RAID Mode Selecting the Striping Block SizeYES Completing the RAID Bios SetupArray 2 Nvidia Mirror 76.33G Cd bootdrv Menu Installing the RAID driversIntroduction of audio connectors Stereo Speakers Connection and Settings5 2- / 4- / 6- / 8- Channel Audio Function Introduction Channel Audio Setup English Step Troubleshooting English English Taiwan Headquarters Contact UsChina Shanghai