Gigabyte GA-K8NE-RH user manual Troubleshooting

Page 76

English

4-2 Troubleshooting

Below is a collection of general asked questions. To check general asked questions based on a specific motherboard model, please log on to http://www.gigabyte.com.tw

Question 1: I cannot see some options that were included in previous BIOS after updating BIOS. Why?

Answer: Some advanced options are hidden in new BIOS version. Please press Ctrl and F1 keys after entering BIOS menu and you will be able to see these options.

Questions 2: Why is the light of my keyboard/optical mouse still on after computer shuts down?

Answer: In some boards, a small amount of electricity is kept on standby after computer shuts down and that's why the light is still on.

Question 3: How do I clear CMOS?

Answer: If your board has a Clear CMOS jumper, please refer to the Clear CMOS steps in the manual. If your board doesn't have such jumper, you can take off the on-board battery to leak voltage to clear CMOS. Please refer to the steps below:

Steps:

1.Turn off power.

2.Disconnect the power cord from MB.

3.Take out the battery gently and put it aside for about 10 minutes (Or you can use a metal object to connect the positive and negative pins in the battery holder to makethem short for one minute).

4.Re-insert the battery to the battery holder.

5.Connect power cord to MB again and turn on power.

6.Press Del to enter BIOS and load Fail-Safe Defaults(or load Optimized Defaults).

7.Save changes and reboot the system.

Question 4: Why do I still get a weak sound after turning up the speaker to the maximum volume?

Answer: Please make sure the speaker you are using is equipped with an internal amplifier. If not, please change another speaker with power/amplifier and try again later.

Question 5: Sometimes I hear different continuous beeps from computer after system boots up. What do these beeps usually stand for?

Answer: The beep codes below may help you identify the possible computer problems. However, they are only for reference purposes. The situations might differ from case to case.

AMI BIOS Beep Codes

*Computer gives 1 short beep when system boots successfully. *Except for beep code 8, these codes are always fatal.

1 beep Refresh failure

2 beeps Parity error

3 beeps Base 64K memory failure

4 beeps Timer not operational

5 beeps Processor error

6 beeps 8042 - gate A20 failure

7 beeps Processor exception interrupt error

8 beeps Display memory read/write failure

9 beeps ROM checksum error

10 beeps CMOS shutdown register read/write error

11 beeps Cache memory bad

AWARD BIOS Beep Codes

1 short: System boots successfully

2 short: CMOS setting error

1 long 1 short: DRAM or M/B error

1 long 2 short: Monitor or display card error

1 long 3 short: Keyboard error

1 long 9 short: BIOS ROM error

Continuous long beeps: DRAM error

Continuous short beeps: Power error

GA-K8NE-RH Motherboard

- 76 -

Image 76
Contents GA-K8NE-RH Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation Item Checklist GA-K8NE-RH Motherboard Layout Block Diagram Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary ALC850 Codec UAJUse of licensed Award Bios Installation of the CPU and Heatsink Installation of the CPUInstallation of Memory Installation of the HeatsinkDDR1 DDR2 DDR3 Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction Side Speaker OutATX12V / ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector SATAII01 / SATAII23 Serial ATA ConnectorFpanel Front Panel Jumper Faudio Front Audio Panel Connector PwrledCdin CD In Connector USB1 / FUSB2 / FUSB3 Front USB ConnectorComb Comb Connector CI Chassis Intrusion, Case OpenBAT Battery Clrcmos Clear CmosEnglish Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. FDh F12 For Boot Menu„ Standard Cmos Features „ Advanced Bios Features„ Power Management Setup „ PnP/PCI ConfigurationIDE Channel 0 Master, Slave, IDE Channel 1 Master, Slave TimeIDE Channel 2/3/4/5 Master Drive a / Drive B Floppy 3 Mode Support for Japan AreaHalt on First / Second / Third Boot Device Hard Disk Boot PriorityBoot Up Floppy Seek Password Check Init Display FirstIDE DMA transfer access Integrated PeripheralsOn-Chip IDE Channel0 On-Chip IDE Channel1IDE Prefetch Mode On-Chip MAC LanNV IDE/SATA RAID function NV Serial-ATAParallel Port Mode ECP Mode Use DMAOnboard Parallel Port On-Chip USBModem Ring On PME Event Wake UpUSB Resume from Suspend Power-On by Alarm Power On By MousePower On By Keyboard KB Power on FunctionPnP/PCI Configurations PC Health Status DDR25VReset Case Open Status Current CPU TemperatureCPU Warning Temperature Case OpenedTemp of FAN turn off Default temperature 0oC Temp Limit of Low Speed Default temperature 20oCTemp Limit of Mid Speed Default temperature 50oC Temp Limit of High Speed Default temperature 60oCHT Frequency ratio MB Intelligent TweakerM.I.TCPU Frequency DDR clock/Timing Mode RAS# to CAS# delay TrcdRow to Row delay Trrd Write Recovery Time TwrWrite-to-Read Delay Twtr Refresh Rate TrefRead Preamble value Async Latency valueTop Performance Set Supervisor/User Password Save & Exit Setup Exit Without SavingDrivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish Unique Software Utilities EasyTune 5 Introduction User Interface OverviewHow to use the Xpress Recovery2 Xpress Recovery2 IntroductionSystem requirements Precautions Main Screen of Xpress Recovery2Limitations Method 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen EnglishCongratulation!! You have updated Bios successfully Bios file becomes F4 after updatingMethod 2 @BIOSTM Utility Methods and stepsEnglish Serial ATA Bios Setting Utility Introduction RAID LevelsConfiguring the Nvidia RAID Bios Entering the RAID Bios SetupUsing the Define a New Array Window Selecting the RAID ModeSelecting the Striping Block Size Assigning the DisksCompleting the RAID Bios Setup YESArray 2 Nvidia Mirror 76.33G Installing the RAID drivers Cd bootdrv MenuStereo Speakers Connection and Settings Introduction of audio connectors5 2- / 4- / 6- / 8- Channel Audio Function Introduction Channel Audio Setup English Step Troubleshooting English English Contact Us Taiwan HeadquartersChina Shanghai

GA-K8NE-RH specifications

The Gigabyte GA-K8NE-RH is a reliable motherboard designed for AMD processors, specifically catering to the Socket 754 form factor. Released during a time when AMD's Athlon 64 processors were gaining popularity, the GA-K8NE-RH stands out for its remarkable performance and a range of features that appealed to both gamers and general users alike.

One of the main highlights of the GA-K8NE-RH is its ability to support AMD’s 64-bit processing technology, allowing users to take full advantage of the enhanced performance capabilities of Athlon 64 CPUs. This motherboard supports memory configurations with up to 4GB of DDR memory, utilizing dual-channel architecture. This dual-channel setup not only boosts memory bandwidth but also improves overall system performance, making it ideal for multitasking and memory-intensive applications.

The GA-K8NE-RH is built on the nForce3 250 chipset, which features an integrated NVIDIA graphics processing unit. This allows for a more streamlined graphic performance, making it suitable for casual gaming and multimedia applications. Furthermore, the integrated Gigabit Ethernet ensures high-speed network connectivity, essential for online gaming and downloading large files.

This motherboard also includes multiple IDE and SATA connectors. With support for SATA II, users can benefit from faster data transfer rates compared to traditional IDE connections. Additionally, the inclusion of RAID support enables users to set up disk redundancy for improved data security or enhanced read/write speeds, depending on their setup.

In terms of audio capabilities, the GA-K8NE-RH features a built-in 6-channel audio codec, providing clear sound quality for an immersive multimedia experience. The onboard PCI Express and PCI slots offer ample expansion opportunities for graphics cards, sound cards, or additional peripherals, making it a flexible choice for various builds.

Moreover, Gigabyte's renowned durability features ensure that the GA-K8NE-RH remains a dependable choice for enthusiasts. The motherboard is equipped with a range of capacitors and solid-state components that contribute to its longevity and stability.

Overall, the Gigabyte GA-K8NE-RH is a well-rounded motherboard that provides excellent performance and versatility for users looking to build a capable AMD-based system. With a combination of stable performance, advanced features, and support for various technologies, it remains an appealing option for users seeking value and reliability in their computing experience.