Gigabyte GA-K8NF-9-RH user manual IDE1 / IDE2 IDE Connector

Page 21

6)IDE1 / IDE2 (IDE Connector)

An IDE device connects to the computer via an IDE connector. One IDE connector can connect to one IDE cable, and the single IDE cable can then connect to two IDE devices (hard drive or optical drive). If you wish to connect two IDE devices, please set the jumper on one IDE device as Master and the other as Slave (for information on settings, please refer to the instructions located on the IDE device). Before attaching the IDE cable, please take note of the foolproof groove in the IDE connector.

40

39

2

1

IDE2 IDE1

7)SATAII0_1 / SATAII2_3 (Serial ATA Connectors, Controlled by nForce4-4X)

Serial ATA can provide up to 150MB/s transfer rate. Please refer to the BIOS setting for the Serial ATA and install the proper driver in order to work properly.

7

1

 

Pin No.

Definition

SATAII_1

1

GND

 

 

 

2

TXP

1

7

SATAII_0

3

TXN

4

GND

 

 

 

7

1

SATAII_3

5

RXN

6

RXP

 

 

 

 

 

 

7

GND

1

7

SATAII_2

 

 

English

- 21 -

Hardware Installation

Image 21
Contents GA-K8NF-9-RH Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation GA-K8NF-9-RH Motherboard Layout Block Diagram Page Installation Notices Considerations Prior to InstallationInstances of Non-Warranty Preparing Your ComputerLAN Feature Summary4Mbit flash ROM Installation of the CPU Installation of the CPU and Fan Heat SinkInstallation of the Fan Heat Sink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Side Speaker Out Connectors IntroductionATX12V / ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power ConnectorIDE1 / IDE2 IDE Connector Pwrled Fpanel Front Panel Jumper Cdin CD In Connector Faudio Front Audio Panel Connector14 F11394 / F21394 Front Ieee 1394 Connectors USB1 / FUSB2 / FUSB3 Front USB ConnectorClrcmos Clear Cmos Main Menu Status Page Setup Menu / Option Page Setup MenuF12 For Boot Menu Main Menu For example Bios Ver. FD„ Advanced Bios Features „ Standard Cmos Features„ Power Management Setup „ PnP/PCI ConfigurationTime IDE Channel 0 Master/Slave IDE Channel 1 Master/SlaveIDE Channel 2/3/4/5 Master Floppy 3 Mode Support for Japan Area Drive a / Drive BHalt on Hard Disk Boot Priority First / Second / Third Boot DeviceBoot Up Floppy Seek Init Display First Password CheckIntegrated Peripherals IDE DMA transfer accessOn-Chip IDE Channel0 On-Chip IDE Channel1IDE Prefetch Mode On-Chip LAN Boot ROMOn-Chip MAC Lan controlled by Vitesse 8201 phy NV IDE/SATA RAID functionECP Mode Use DMA Parallel Port ModeOnboard Serial Port Onboard Parallel PortPower Management Setup Power On by Keyboard Power On by MouseKB Power on Password AC Back FunctionPnP/PCI Configurations PC Health Status Current CPU TemperatureCurrent VoltageV Vcore / DDR25V / +3.3V / +12V Current CPU/SYSTEM FAN Speed RPMTemp of FAN turn off Default temperature 0oC CPU Warning TemperatureCPU FAN Fail Warning CPU Smart FAN Control NoteTemp Limit of Mid Speed Default temperature 50oC Temp Limit of Low Speed Default temperature 20oCTemp Limit of High Speed Default temperature 60oC Temp of full FAN Speed Default temperature 70oCCPU Frequency HT Frequency RatioK8 CPU Clock Ratio Current DDR speedChipset core PCI-E voltage HT-Link voltage controlDDR voltage control Top Performance Set Supervisor/User Password Exit Without Saving Save & Exit SetupEnglish Install Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish Unique Software Utilities EasyTune 5 IntroductionUser Interface Overview Xpress Recovery2 Introduction How to use the Xpress Recovery2System requirements Main Screen of Xpress Recovery2 PrecautionsLimitations Flash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Task menu for Dual Bios utility Exploring the Q-FlashTM / Dual Bios utility screenEntering the Q-FlashTMutility Task menu for Q-Flash utilitySteps Using the Q-FlashTMutilityYou can repeat to Press Y on your keyboard to save and exit FlashTMutility bar Exploring the Q-FlashTMutility screenCongratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM UtilityEnglish Configuring Sata Hard Drives To configure Sata hard drives, follow the steps belowInstall Sata hard drives in your system RAID Appendix Step Save and exit Bios Setup GA-K8NF-9-RH Motherboard Configuring RAID set in RAID Bios YES Nvidia Making a Sata Driver Disk Cd bootdrv MenuInstalling Sata controller driver during OS installation NForce Storage Controller Enter= Continue R=Repair F3=Exit Solutions Configuring a bootable RAID array with Microsoft WindowsYES English Introduction of audio connectors Stereo Speakers Connection and Settings5 2- / 4- / 6- / 8- Channel Audio Function Introduction Channel Audio Setup English Step Troubleshooting English English English Taiwan Headquarters Contact UsGigabyte Global Service System