Gigabyte GA-K8NF-9-RH user manual NForce Storage Controller

Page 74

English

Step 3:

If Setup correctly recognizes the driver in the floppy disk, a controller menu similar to Figure 16 below will appear. Use the ARROW keys to select NVIDIA RAID CLASS DRIVER(Note) (Figure 16) and press ENTER. Later, when a screen similar to Figure 17 appears, you must press S to select additional driver. The screen will return to previous screen as shown in Figure 16. Select NVIDIA NForce Storage Controller and press ENTER.

Windows Setup

You have chosen to configure a SCSI Adapter for use with Windows, using a device support disk provided by an adapter manufacturer.

Select the SCSI Adapter you want from the following list, or press ESC to return to the previous screen.

NVIDIA RAID CLASS DRIVER (required)

NVIDIA nForce Storage Controller (required)

ENTER=Select F3=Exit

Figure 16

Windows Setup

Setup will load support for the following mass storage device(s):

NVIDIA RAID CLASS DRIVER (required)

*To specify additional SCSI adapters, CD-ROM drives, or special disk controllers for use with Windows, including those for which you have a device support disk from a mass storage device manufacturer, press S.

*If you do not have any device support disks from a mass storage device manufacturer, or do not want to specify additional mass storage devices for use with Windows, press ENTER.

S=Specify Additional Device ENTER=Continue F3=Exit

Figure 17

If a message appears saying one or some file(s) cannot be found, please check the floppy disk or copy the correct SATA driver again from the motherboard driver CD.

(Note) If you want to create RAID, select both NVIDIA RAID CLASS DRIVER and then NVIDIA

NForce Storage Controller.

If you do not create RAID, select NVIDIA NForce Storage Controller only.

GA-K8NF-9-RH Motherboard

- 74 -

Image 74
Contents GA-K8NF-9-RH Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-K8NF-9-RH Motherboard Layout Block Diagram Page Instances of Non-Warranty Considerations Prior to InstallationInstallation Notices Preparing Your ComputerFeature Summary LAN4Mbit flash ROM Installation of the CPU and Fan Heat Sink Installation of the CPUInstallation of the Fan Heat Sink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction Side Speaker OutATX12V / ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector Pwrled Fpanel Front Panel Jumper Faudio Front Audio Panel Connector Cdin CD In ConnectorUSB1 / FUSB2 / FUSB3 Front USB Connector 14 F11394 / F21394 Front Ieee 1394 ConnectorsClrcmos Clear Cmos Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. FD F12 For Boot Menu„ Power Management Setup „ Standard Cmos Features„ Advanced Bios Features „ PnP/PCI ConfigurationIDE Channel 2/3/4/5 Master TimeIDE Channel 0 Master/Slave IDE Channel 1 Master/Slave Halt on Floppy 3 Mode Support for Japan AreaDrive a / Drive B Boot Up Floppy Seek Hard Disk Boot PriorityFirst / Second / Third Boot Device Password Check Init Display FirstOn-Chip IDE Channel0 IDE DMA transfer accessIntegrated Peripherals On-Chip IDE Channel1On-Chip MAC Lan controlled by Vitesse 8201 phy On-Chip LAN Boot ROMIDE Prefetch Mode NV IDE/SATA RAID functionOnboard Serial Port Parallel Port ModeECP Mode Use DMA Onboard Parallel PortPower Management Setup KB Power on Password Power On by MousePower On by Keyboard AC Back FunctionPnP/PCI Configurations Current VoltageV Vcore / DDR25V / +3.3V / +12V Current CPU TemperaturePC Health Status Current CPU/SYSTEM FAN Speed RPMCPU FAN Fail Warning CPU Warning TemperatureTemp of FAN turn off Default temperature 0oC CPU Smart FAN Control NoteTemp Limit of High Speed Default temperature 60oC Temp Limit of Low Speed Default temperature 20oCTemp Limit of Mid Speed Default temperature 50oC Temp of full FAN Speed Default temperature 70oCK8 CPU Clock Ratio HT Frequency RatioCPU Frequency Current DDR speedDDR voltage control Chipset core PCI-E voltageHT-Link voltage control Top Performance Set Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Drivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish User Interface Overview Unique Software UtilitiesEasyTune 5 Introduction System requirements Xpress Recovery2 IntroductionHow to use the Xpress Recovery2 Limitations Main Screen of Xpress Recovery2Precautions Before You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Entering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Press Y on your keyboard to save and exit Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Install Sata hard drives in your system Configuring Sata Hard DrivesTo configure Sata hard drives, follow the steps below RAID Appendix Step Save and exit Bios Setup GA-K8NF-9-RH Motherboard Configuring RAID set in RAID Bios YES Nvidia Cd bootdrv Menu Making a Sata Driver DiskInstalling Sata controller driver during OS installation NForce Storage Controller Enter= Continue R=Repair F3=Exit Configuring a bootable RAID array with Microsoft Windows SolutionsYES English 5 2- / 4- / 6- / 8- Channel Audio Function Introduction Introduction of audio connectorsStereo Speakers Connection and Settings Channel Audio Setup English Step Troubleshooting English English English Contact Us Taiwan HeadquartersGigabyte Global Service System