Gigabyte GA-8I845GVM775 user manual Integrated Peripherals

Page 32

English

2-3 Integrated Peripherals

CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

Integrated Peripherals

On-Chip Primary PCI IDE

[Enabled]

On-Chip Secondary PCI IDE

[Enabled]

IDE1 Conductor Cable

[Auto]

IDE2 Conductor Cable

[Auto]

USB Controller

[Enabled]

USB Keyboard Support

[Disabled]

USB Mouse Support

[Disabled]

AC97 Audio

[Auto]

Onboard H/W LAN

[Enabled]

Onboard Serial Port 1

[3F8/IRQ4]

Onboard Serial Port 2

[2F8/IRQ3]

UART Mode Select

[Normal]

x UR2 Duplex Mode

[Half]

Onboard Parallel Port

[378/IRQ7]

Parallel Port Mode

[SPP]

x ECP Mode Use DMA

3

Ite m Help

Menu Level `

KLJI: Move

Enter: Select

+/-/PU/PD: Value

F10: Save

ESC: Exit

F1:General Help

F5: Previous Values

F6: Fail-Safe Default

 

F7: Optimized Defaults

On-Chip Primary PCI IDE

Enabled

Enable onboard 1st channel IDE port. (Default value)

Disabled

Disable onboard 1st channel IDE port.

On-Chip Secondary PCI IDE

Enabled

Enable onboard 2nd channel IDE port. (Default value)

Disabled

Disable onboard 2nd channel IDE port.

IDE1 Conductor Cable

Auto

Will be automatically detected by BIOS. (Default Value)

ATA66/100

Set IDE1 Conductor Cable to ATA66/100 (Please make sure your IDE

 

device and cable is compatible with ATA66/100).

ATA33

Set IDE1 Conductor Cable to ATA33 (Please make sure your IDE device

 

and cable is compatible with ATA33).

IDE2 Conductor Cable

Auto

Will be automatically detected by BIOS. (Default Value)

ATA66/100

Set IDE2 Conductor Cable to ATA66/100 (Please make sure your IDE

 

device and cable is compatible with ATA66/100).

ATA33

Set IDE2 Conductor Cable to ATA33 (Please make sure your IDE device

 

and cable is compatible with ATA33).

USB Controller

 

Enabled

Enable USB Controller. (Default value)

Disabled

Disable USB Controller.

GA-8I845GVM775 Motherboard

- 32 -

Image 32
Contents GA-8I845GVM775 Motherboard Copyright Product Manual ClassificationTable of Content Install Drivers GA-8I845GVM775 Motherboard Layout Block Diagram Page Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary BiosInstallation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory Install expansion cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD Floppy ConnectorFaudio Front Audio Connector IDE1 / IDE2 IDE1 / IDE2 ConnectorFpanel Front Panel Jumper Auxin AUX In Connector Cdin CDSpdifio Spdif In/Out Connector Comb Serial Port ConnectorFUSB1 Front USB Connector, Yellow Clrcmos Clear CmosBATBattery CI Case OpenStatus Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. E2 „ Exit Without Saving „ Set User Password„ Save & Exit Setup IDE Primary/ Secondary Master, Slave Standard Cmos FeaturesTime Floppy 3 Mode Support for Japan Area Drive a / Drive BHalt on MemoryBoot Up Floppy Seek Advanced Bios FeaturesFirst / Second / Third Boot Device Password Check CPU Hyper-ThreadingLimit Cpuid Max. to Init Display FirstIntegrated Peripherals Uart Mode Select UR2 Duplex ModeUSB Keyboard Support USB Mouse SupportECP Mode Use DMA Power Management SetupParallel Port Mode Resume by Alarm Power On By MousePower On By Keyboard KB Power on PasswordPnP/PCI Configurations PCI 1 IRQ AssignmentPC Health Status Frequency/Voltage Control CPU/SYSTEM FAN Fail WarningCPU Smart FAN Control CPU Clock RatioCPU Host Clock Control CPU Host Frequency MHzFixed PCI/AGP FrequencyMhz Host/DRAM Clock RatioLoad Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingInstall Chipset Drivers Pictures below are shown in Windows XPItem Description „ @BIOS Software ApplicationSoftware Information Hardware InformationEasyTune 4 Installation Unique Software UtilitiesHow to use the Xpress Recovery Xpress Recovery IntroductionWhat is Xpress Recovery ? F9 For Xpress Recovery Remove Backup Image  Remove backup image. Are you sure? Y/N Exit and RestartBefore You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen EnglishCongratulation!! You have updated Bios successfully Bios file becomes F4 after updatingMethod 2 @BIOSTM Utility Methods and stepsEnglish Stereo Speakers Connection and Settings 4 2- / 4- / 6- Channel Audio Function IntroductionChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode English Basic & Advanced 6 Channel Analog Audio Output Mode Notes Spdif Output Device Optional Device Auto-detecting Introduction of audio connectorsJack-Sensing Introduction Manual setting Troubleshooting AMI Bios Beep Codes English Contact Us Taiwan HeadquartersChina Shanghai