Gigabyte GA-8I845GVM775 user manual Part Two

Page 55

6.Press Del to enter BIOS menu after system reboots. When you are in BIOS menu, move to

Load Fail-Safe Defaults item and press Enter to load BIOS Fail-Safe Defaults. Normally the system redetects all devices after BIOS has been upgraded. Therefore, we highly recommend reloading the BIOS defaults after BIOS has been upgraded.

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

Standard CMOS Features

Select Language

Advanced BIOS Features

Load Fail-Safe Defaults

Integrated Peripherals

Load Optimized Defaults

Power Management Setup

Load Fail-Safe Defaults (Y/N)?Set SupervisorY

Password

PnP/PCI Configurations

Set User Password

PC Health Status

Save & Exit Setup

MB Intelligent Tweaker(M.I.T.)

Exit Without Saving

ESC: Quit

F3: Change Language

F8: Dual BIOS/Q-Flash

F10: Save & Exit Setup

 

Time, Date, Hard Disk Type...

 

Press Y on your keyboard to load defaults.

7.Select Save & Exit Setup item to save the settings to CMOS and exit the BIOS menu. System will reboot after you exit the BIOS menu. The procedure is completed.

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

Standard CMOS Features

 

Select Language

Advanced BIOS Features

 

Load Fail-Safe Defaults

Integrated Peripherals

 

Load Optimized Defaults

Power Management Setup

Save to CMOS and EXIT (Y/N)?Set SupervisorY

Password

PnP/PCI Configurations

 

Set User Password

PC Health Status

 

Save & Exit Setup

MB Intelligent Tweaker(M.I.T.)

Exit Without Saving

ESC: Quit

 

F3: Change Language

F8: Dual BIOS/Q-Flash

 

F10: Save & Exit Setup

 

 

Time, Date, Hard Disk Type...

 

 

Press Y on your keyboard to save and exit.

Part Two:

 

 

 

Updating BIOS with Q-FlashTMUtility on Single-BIOS Motherboards.

This part guides users of single-BIOS motherboards how to update BIOS using the Q-FlashTMutility.

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

Standard CMOS Features

Top Performance

Advanced BIOS Features

Load Fail-Safe Defaults

Integrated Peripherals

Load Optimized Defaults

Power Management Setup

Set Supervisor Password

PnP/PCI Configurations

Set User Password

PC Health Status

Save & Exit Setup

MB Intelligent Tweaker(M.I.T.)

Exit Without Saving

ESC: Quit

F3: Change Language

F8: Q-Flash

F10: Save & Exit Setup

 

Time, Date, Hard Disk Type...

English

- 55 -

Appendix

Image 55
Contents GA-8I845GVM775 Motherboard Product Manual Classification CopyrightTable of Content Install Drivers GA-8I845GVM775 Motherboard Layout Block Diagram Page Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantyBios Feature SummaryInstallation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of Memory Install expansion cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector FDD Floppy Connector Cpufan / Sysfan Cooler Fan Power ConnectorIDE1 / IDE2 IDE1 / IDE2 Connector Faudio Front Audio ConnectorFpanel Front Panel Jumper Cdin CD Auxin AUX In ConnectorComb Serial Port Connector Spdifio Spdif In/Out ConnectorClrcmos Clear Cmos FUSB1 Front USB Connector, YellowCI Case Open BATBatteryMain Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. E2 „ Save & Exit Setup „ Set User Password„ Exit Without Saving Time Standard Cmos FeaturesIDE Primary/ Secondary Master, Slave Memory Floppy 3 Mode Support for Japan AreaDrive a / Drive B Halt onFirst / Second / Third Boot Device Advanced Bios FeaturesBoot Up Floppy Seek Init Display First Password CheckCPU Hyper-Threading Limit Cpuid Max. toIntegrated Peripherals USB Mouse Support Uart Mode SelectUR2 Duplex Mode USB Keyboard SupportParallel Port Mode Power Management SetupECP Mode Use DMA KB Power on Password Resume by AlarmPower On By Mouse Power On By KeyboardPCI 1 IRQ Assignment PnP/PCI ConfigurationsPC Health Status CPU Clock Ratio Frequency/Voltage ControlCPU/SYSTEM FAN Fail Warning CPU Smart FAN ControlHost/DRAM Clock Ratio CPU Host Clock ControlCPU Host Frequency MHz Fixed PCI/AGP FrequencyMhzLoad Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupPictures below are shown in Windows XP Install Chipset DriversItem Description Software Application „ @BIOSHardware Information Software InformationUnique Software Utilities EasyTune 4 InstallationWhat is Xpress Recovery ? Xpress Recovery IntroductionHow to use the Xpress Recovery F9 For Xpress Recovery Exit and Restart Remove Backup Image  Remove backup image. Are you sure? Y/NMethod 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Task menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two English Exploring the Q-FlashTMutility screenBios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish 4 2- / 4- / 6- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode English Basic & Advanced 6 Channel Analog Audio Output Mode Notes Spdif Output Device Optional Device Jack-Sensing Introduction Introduction of audio connectorsAuto-detecting Manual setting Troubleshooting AMI Bios Beep Codes English Taiwan Headquarters Contact UsChina Shanghai