Gigabyte GA-8I845GVM775 Frequency/Voltage Control, CPU/SYSTEM FAN Fail Warning, CPU Clock Ratio

Page 38

English

CPU/SYSTEM FAN Fail Warning

Disabled

Fan warning function disable. (Default value)

Enabled

Fan warning function enable.

CPU Smart FAN Control

Disabled

Disable this function.

Enabled

Enable CPU Smart Fan control function. (Default value)

 

a. When the CPU temperature is higher than 65 degrees Celsius, CPU fan

 

will run at full speed.

 

b. The speed of CPU fan will increase linearly depand on the temperature

 

if the temperature is more than 41 degree and less than 65 degree.

 

c . When the CPU temperature is lower than 40 degrees Celsius, CPU fan

 

willbe disable.

2-7

Frequency/Voltage Control

 

 

 

 

 

 

 

 

 

CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

 

 

 

 

MB Intelligent Tweaker(M.I.T.)

 

 

 

CPU Clock Ratio

[15X]

 

 

Item Help

 

CPU Host Clock Control

[Disabled]

 

Menu Level `

X

CPU Host Frequency (Mhz)

133

 

 

 

X

Fixed PCI/AGP Frequency

33/66

 

 

 

 

Host/DRAM clock ratio

[Auto]

 

 

 

X

Memory Frequency (Mhz)

333

 

 

 

X

PCI/AGP Frequency (Mhz)

33/66

 

 

 

KLJI: Move

Enter: Select

+/-/PU/PD: Value

F10: Save

ESC: Exit

F1:General Help

 

F5: Previous Values

F6: Fail-Safe Default

 

F7: Optimized Defaults

 

 

 

 

 

 

 

Incorrect using these features may cause your system broken. For power end-user use only.

CPU Clock Ratio

This setup option will automatically assign by CPU detection.

The option will display "Locked" and read only if the CPU ratio is not changeable.

GA-8I845GVM775 Motherboard

- 38 -

Image 38
Contents GA-8I845GVM775 Motherboard Copyright Product Manual ClassificationTable of Content Install Drivers GA-8I845GVM775 Motherboard Layout Block Diagram Page Instances of Non-Warranty Considerations Prior to InstallationInstallation Notices Preparing Your ComputerFeature Summary BiosInstallation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory Install expansion cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD Floppy ConnectorFaudio Front Audio Connector IDE1 / IDE2 IDE1 / IDE2 ConnectorFpanel Front Panel Jumper Auxin AUX In Connector Cdin CDSpdifio Spdif In/Out Connector Comb Serial Port ConnectorFUSB1 Front USB Connector, Yellow Clrcmos Clear CmosBATBattery CI Case OpenStatus Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. E2 „ Exit Without Saving „ Set User Password„ Save & Exit Setup IDE Primary/ Secondary Master, Slave Standard Cmos FeaturesTime Halt on Floppy 3 Mode Support for Japan AreaDrive a / Drive B MemoryBoot Up Floppy Seek Advanced Bios FeaturesFirst / Second / Third Boot Device Limit Cpuid Max. to Password CheckCPU Hyper-Threading Init Display FirstIntegrated Peripherals USB Keyboard Support Uart Mode SelectUR2 Duplex Mode USB Mouse SupportECP Mode Use DMA Power Management SetupParallel Port Mode Power On By Keyboard Resume by AlarmPower On By Mouse KB Power on PasswordPnP/PCI Configurations PCI 1 IRQ AssignmentPC Health Status CPU Smart FAN Control Frequency/Voltage ControlCPU/SYSTEM FAN Fail Warning CPU Clock RatioFixed PCI/AGP FrequencyMhz CPU Host Clock ControlCPU Host Frequency MHz Host/DRAM Clock RatioLoad Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingInstall Chipset Drivers Pictures below are shown in Windows XPItem Description „ @BIOS Software ApplicationSoftware Information Hardware InformationEasyTune 4 Installation Unique Software UtilitiesHow to use the Xpress Recovery Xpress Recovery IntroductionWhat is Xpress Recovery ? F9 For Xpress Recovery Remove Backup Image  Remove backup image. Are you sure? Y/N Exit and RestartBefore You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Entering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen EnglishCongratulation!! You have updated Bios successfully Bios file becomes F4 after updatingMethod 2 @BIOSTM Utility Methods and stepsEnglish Stereo Speakers Connection and Settings 4 2- / 4- / 6- Channel Audio Function IntroductionChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode English Basic & Advanced 6 Channel Analog Audio Output Mode Notes Spdif Output Device Optional Device Auto-detecting Introduction of audio connectorsJack-Sensing Introduction Manual setting Troubleshooting AMI Bios Beep Codes English Contact Us Taiwan HeadquartersChina Shanghai