Gigabyte GA-8I945PLGE-RH user manual Integrated Peripherals

Page 36

English

2-3 Integrated Peripherals

CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

Integrated Peripherals

On-Chip Primary PCI IDE

[Enabled]

On-Chip SATA Mode

[Auto]

x PATA IDE Set to

Ch.0 Master/Slave

SATA Port 0/2 Set to

Ch.2 Master/Slave

SATA Port 1/3 Set to

Ch.3 Master/Slave

USB Controller

[Enabled]

USB 2.0 Controller

[Enabled]

USB Keyboard Support

[Disabled]

USB Mouse Support

[Disabled]

Legacy USB storage detect

[Enabled]

Azalia Codec

[Auto]

Onboard H/W LAN

[Enabled]

OnBoard LAN Boot ROM

[Disabled]

Onboard Serial Port 1

[3F8/IRQ4]

i-Lock

[Enabled]

Onboard Parallel Port

[378/IRQ7]

Parallel Port Mode

[SPP]

x ECP Mode Use DMA

3

Item Help

Menu Level`

KLJI: Move

Enter: Select

+/-/PU/PD: Value

F10: Save

ESC: Exit

F1: General Help

F5: Previous Values

F6: Fail-Safe Defaults

 

F7: Optimized Defaults

On-Chip Primary PCI IDE

Enabled

Enable onboard 1st channel IDE port. (Default value)

Disabled

Disable onboard 1st channel IDE port.

On-Chip SATA Mode

Disabled

Disable this function.

Auto

BIOS will auto detect. (Default value)

Combined

Set On-Chip SATA mode to Combined, you can use up to 4 HDDs on

 

the motherboard; 2 for SATA and the other for PATA.

Enhanced

Set On-Chip SATA mode to Enhanced, the motherboard allows up to 6

 

HDDs to use; 4 SATA HDDs plus PATA HDDs.

Non-Combined

Set On-Chip SATA mode to Non-Combined, SATA will be simulated to

 

PATA mode. Support a maximum of 4 SATA devices. PATA devices will be

 

ignored.

PATA IDE Set to

Ch.1

Master/Slave

Set PATA IDE to Ch. 1 Master/Slave.

Ch.0

Master/Slave

Set PATA IDE to Ch. 0 Master/Slave. (Default value)

SATA Port 0/2 Set to

This value will auto make by the setting "On-Chip SATA Mode" and "PATA IDE Set to".

If PATA IDE were set to Ch. 1 Master/Slave,this function will auto set to Ch. 0 Master/Slave.

SATA Port 1/3 Set to

This value will auto make by the setting "On-Chip SATA Mode" and "PATA IDE Set to".

If PATA IDE were set to Ch. 0 Master/Slave,this function will auto set to Ch. 1 Master/Slave.

GA-8I945PLGE-RH Motherboard

- 36 -

Image 36
Contents GA-8I945PLGE-RH Motherboard Copyright Product Manual ClassificationTable of Contents Install Drivers GA-8I945PLGE-RH Motherboard Layout Block Diagram Page Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary CPU4Mbit flash ROM Installation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction Center/Subwoofer Speaker OutSide Speaker Out ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD Floppy ConnectorIDE1 IDE Connector SATAII0/SATAII1/SATAII2/SATAII3 Sata 3Gb/s ConnectorFaudio Front Audio Connector PwrledFpanel Front Panel Jumper Cdin CD Spdifi SpdifFUSB1 / FUSB2 Front USB Connectors RfidCI Chassis Intrusion, Case Open Clrcmos Clear CmosBATBattery English Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. F1a F12 For Boot Menu„ Standard Cmos Features „ Advanced Bios Features„ Power Management Setup „ PnP/PCI ConfigurationsStandard Cmos Features TimeIDE Channel 0 Master, Slave IDE Channel 2/3 Master, SlaveFloppy 3 Mode Support for Japan Area Drive a / Drive BHalt on MemoryAdvanced Bios Features Hard Disk Boot PriorityFirst / Second / Third Boot Device Password CheckCPU Hyper-Threading Limit Cpuid Max. toNo-Execute Memory Protect Note CPU Enhanced Halt C1E NoteIntegrated Peripherals OnBoard LAN Boot ROM USB ControllerUSB 2.0 Controller USB Keyboard SupportPower Management Setup Parallel Port ModeECP Mode Use DMA Resume by Alarm Power On By MousePower On By Keyboard KB Power on PasswordPnP/PCI Configurations PCI 1 IRQ AssignmentPC Health Status CPU Smart FAN Mode CPU Smart FAN ControlMB Intelligent TweakerM.I.T CPU Clock Ratio NoteM Note Robust Graphics BoosterCPU Host Clock Control CPU Host Frequency MhzPCI Express Frequency Mhz System Memory MultiplierPCI-E OverVoltage Control FSB OverVoltage ControlCPU Voltage Control Normal CPU VcoreLoad Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingInstall Drivers Install Chipset DriversSoftware Applications Driver CD InformationHardware Information Contact UsEnglish Unique Software Utilities EasyTune 5 Introduction User Interface OverviewXpress Recovery2 Introduction How to use the Xpress Recovery2System requirements Main Screen of Xpress Recovery2 PrecautionsLimitations Flash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen EnglishCongratulation!! You have updated Bios successfully Bios file becomes F4 after updatingMethod 2 @BIOSTM Utility Methods and stepsEnglish Stereo Speakers Connection and Settings 4 2- / 4- / 6- / 8- Channel Audio Function IntroductionChannel Audio Setup English English Sound Effect Configuration Troubleshooting AMI Bios Beep CodesEnglish Appendix English English English English English Contact Us Taiwan HeadquartersChina Shanghai