Gigabyte GA-8I945PLGE-RH PCI-E OverVoltage Control, FSB OverVoltage Control, CPU Voltage Control

Page 45

PCI-E OverVoltage Control

Normal	Set PCI-E OverVoltrage Control to Normal. (Default value)
+0.1V	Set PCI-E OverVoltrage Control to +0.1V.
+0.2V	Set PCI-E OverVoltrage Control to +0.2V.
+0.3V	Set PCI-E OverVoltrage Control to +0.3V.

Incorrect using it may cause your system broken. For power End-User use only!

FSB OverVoltage Control

Normal	Set FSB OverVoltage Control to Normal. (Default value)
+0.1V	Set FSB OverVoltage Control to +0.1V.
+0.2V	Set FSB OverVoltage Control to +0.2V.
+0.3V	Set FSB OverVoltage Control to +0.3V.

CPU Voltage Control

Supports adjustable CPU Vcore from 0.8375V to 1.6000V. (Default value: Normal)

Normal CPU Vcore

Display your CPU Vcore Voltage.

English

- 45 -

BIOS Setup

Image 45

Contents GA-8I945PLGE-RH Motherboard Product Manual Classification CopyrightTable of Contents Install Drivers GA-8I945PLGE-RH Motherboard Layout Block Diagram Page Installation Notices Considerations Prior to InstallationInstances of Non-Warranty Preparing Your ComputerCPU Feature Summary4Mbit flash ROM Installation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction Center/Subwoofer Speaker OutSide Speaker Out ATX12V/ATX Power Connector FDD Floppy Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATAII0/SATAII1/SATAII2/SATAII3 Sata 3Gb/s Connector IDE1 IDE ConnectorPwrled Faudio Front Audio ConnectorFpanel Front Panel Jumper Spdifi Spdif Cdin CDRfid FUSB1 / FUSB2 Front USB ConnectorsClrcmos Clear Cmos CI Chassis Intrusion, Case OpenBATBattery English Main Menu Status Page Setup Menu / Option Page Setup MenuF12 For Boot Menu Main Menu For example Bios Ver. F1a„ Advanced Bios Features „ Standard Cmos Features„ Power Management Setup „ PnP/PCI ConfigurationsTime Standard Cmos FeaturesIDE Channel 0 Master, Slave IDE Channel 2/3 Master, SlaveDrive a / Drive B Floppy 3 Mode Support for Japan AreaHalt on MemoryHard Disk Boot Priority Advanced Bios FeaturesFirst / Second / Third Boot Device Password CheckLimit Cpuid Max. to CPU Hyper-ThreadingNo-Execute Memory Protect Note CPU Enhanced Halt C1E NoteIntegrated Peripherals USB Controller OnBoard LAN Boot ROMUSB 2.0 Controller USB Keyboard SupportPower Management Setup Parallel Port ModeECP Mode Use DMA Power On By Mouse Resume by AlarmPower On By Keyboard KB Power on PasswordPCI 1 IRQ Assignment PnP/PCI ConfigurationsPC Health Status CPU Smart FAN Control CPU Smart FAN ModeCPU Clock Ratio Note MB Intelligent TweakerM.I.TM Note Robust Graphics BoosterCPU Host Frequency Mhz CPU Host Clock ControlPCI Express Frequency Mhz System Memory MultiplierFSB OverVoltage Control PCI-E OverVoltage ControlCPU Voltage Control Normal CPU VcoreLoad Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupInstall Chipset Drivers Install DriversDriver CD Information Software ApplicationsContact Us Hardware InformationEnglish Unique Software Utilities User Interface Overview EasyTune 5 IntroductionXpress Recovery2 Introduction How to use the Xpress Recovery2System requirements Main Screen of Xpress Recovery2 PrecautionsLimitations Flash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Task menu for Dual Bios utility Exploring the Q-FlashTM / Dual Bios utility screenEntering the Q-FlashTMutility Task menu for Q-Flash utilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two English Exploring the Q-FlashTMutility screenBios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish 4 2- / 4- / 6- / 8- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English English Sound Effect Configuration AMI Bios Beep Codes TroubleshootingEnglish Appendix English English English English English Taiwan Headquarters Contact UsChina Shanghai