Gigabyte GA-8I945PLGE-RH user manual Part Two

Page 61

6.Press Del to enter BIOS menu after system reboots. When you are in BIOS menu, move to

Load Fail-Safe Defaults item and press Enter to load BIOS Fail-Safe Defaults. Normally the system redetects all devices after BIOS has been upgraded. Therefore, we highly recommend reloading the BIOS defaults after BIOS has been upgraded.

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

Standard CMOS Features	Select Language
Advanced BIOS Features	Load Fail-Safe Defaults
Integrated Peripherals	Load Optimized Defaults
Power Management Setup	Load Fail-Safe Defaults (Y/N)?Set SupervisorY	Password
PnP/PCI Configurations	Set User Password
PC Health Status	Save & Exit Setup
MB Intelligent Tweaker(M.I.T.)	Exit Without Saving
ESC: Quit	F3: Change Language
F8: Dual BIOS/Q-Flash	F10: Save & Exit Setup
	Time, Date, Hard Disk Type...

Press Y on your keyboard to load defaults.

7.Select Save & Exit Setup item to save the settings to CMOS and exit the BIOS menu. System will reboot after you exit the BIOS menu. The procedure is completed.

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

Standard CMOS Features		Select Language
Advanced BIOS Features		Load Fail-Safe Defaults
Integrated Peripherals		Load Optimized Defaults
Power Management Setup	Save to CMOS and EXIT (Y/N)?Set SupervisorY		Password
PnP/PCI Configurations		Set User Password
PC Health Status		Save & Exit Setup
MB Intelligent Tweaker(M.I.T.)		Exit Without Saving
ESC: Quit		F3: Change Language
F8: Dual BIOS/Q-Flash		F10: Save & Exit Setup
		Time, Date, Hard Disk Type...
	Press Y on your keyboard to save and exit.
Part Two:

Updating BIOS with Q-FlashTMUtility on Single-BIOS Motherboards.

This part guides users of single-BIOS motherboards how to update BIOS using the Q-FlashTMutility.

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

Standard CMOS Features	Top Performance
Advanced BIOS Features	Load Fail-Safe Defaults
Integrated Peripherals	Load Optimized Defaults
Power Management Setup	Set Supervisor Password
PnP/PCI Configurations	Set User Password
PC Health Status	Save & Exit Setup
MB Intelligent Tweaker(M.I.T.)	Exit Without Saving
ESC: Quit	F3: Change Language
F8: Q-Flash	F10: Save & Exit Setup
	Time, Date, Hard Disk Type...

English

- 61 -

Appendix

Image 61

Contents GA-8I945PLGE-RH Motherboard Product Manual Classification CopyrightTable of Contents Install Drivers GA-8I945PLGE-RH Motherboard Layout Block Diagram Page Installation Notices Considerations Prior to InstallationInstances of Non-Warranty Preparing Your ComputerCPU Feature Summary4Mbit flash ROM Installation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Center/Subwoofer Speaker Out Connectors IntroductionSide Speaker Out ATX12V/ATX Power Connector FDD Floppy Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATAII0/SATAII1/SATAII2/SATAII3 Sata 3Gb/s Connector IDE1 IDE ConnectorPwrled Faudio Front Audio ConnectorFpanel Front Panel Jumper Spdifi Spdif Cdin CDRfid FUSB1 / FUSB2 Front USB ConnectorsClrcmos Clear Cmos CI Chassis Intrusion, Case OpenBATBattery English Main Menu Status Page Setup Menu / Option Page Setup MenuF12 For Boot Menu Main Menu For example Bios Ver. F1a„ Advanced Bios Features „ Standard Cmos Features„ Power Management Setup „ PnP/PCI ConfigurationsTime Standard Cmos FeaturesIDE Channel 0 Master, Slave IDE Channel 2/3 Master, SlaveDrive a / Drive B Floppy 3 Mode Support for Japan AreaHalt on MemoryHard Disk Boot Priority Advanced Bios FeaturesFirst / Second / Third Boot Device Password CheckLimit Cpuid Max. to CPU Hyper-ThreadingNo-Execute Memory Protect Note CPU Enhanced Halt C1E NoteIntegrated Peripherals USB Controller OnBoard LAN Boot ROMUSB 2.0 Controller USB Keyboard SupportParallel Port Mode Power Management SetupECP Mode Use DMA Power On By Mouse Resume by AlarmPower On By Keyboard KB Power on PasswordPCI 1 IRQ Assignment PnP/PCI ConfigurationsPC Health Status CPU Smart FAN Control CPU Smart FAN ModeCPU Clock Ratio Note MB Intelligent TweakerM.I.TM Note Robust Graphics BoosterCPU Host Frequency Mhz CPU Host Clock ControlPCI Express Frequency Mhz System Memory MultiplierFSB OverVoltage Control PCI-E OverVoltage ControlCPU Voltage Control Normal CPU VcoreLoad Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupInstall Chipset Drivers Install DriversDriver CD Information Software ApplicationsContact Us Hardware InformationEnglish Unique Software Utilities User Interface Overview EasyTune 5 IntroductionHow to use the Xpress Recovery2 Xpress Recovery2 IntroductionSystem requirements Precautions Main Screen of Xpress Recovery2Limitations Method 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Task menu for Dual Bios utility Exploring the Q-FlashTM / Dual Bios utility screenEntering the Q-FlashTMutility Task menu for Q-Flash utilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two English Exploring the Q-FlashTMutility screenBios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish 4 2- / 4- / 6- / 8- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English English Sound Effect Configuration AMI Bios Beep Codes TroubleshootingEnglish Appendix English English English English English Taiwan Headquarters Contact UsChina Shanghai