Gigabyte GA-8I915MD-GV user manual Integrated Peripherals

Page 38

English

2-3 Integrated Peripherals

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

Integrated Peripherals

On-Chip Primary PCI IDE

[Enabled]

On-Chip SATA Mode

[Auto]

x PATA IDE Set to

Ch.0 Master/Slave

SATA Port 0 Set to

Ch.2 Master/Slave

SATA Port 1 Set to

Ch.3 Master/Slave

USB Controller

[Enabled]

USB 2.0 Controller

[Enabled]

USB Keyboard Support

[Disabled]

USB Mouse Support

[Disabled]

AC97 Audio

[Auto]

Onboard H/W LAN

[Enabled]

OnBoard LAN Boot ROM

[Disabled]

Onboard Serial Port 1

[3F8/IRQ4]

Onboard Serial Port 2

[2F8/IRQ3]

Onboard Parallel Port

[378/IRQ7]

Parallel Port Mode

[SPP]

x ECP Mode Use DMA

3

Item Help

Menu Level`

KLJI: Move

Enter: Select

+/-/PU/PD: Value

F10: Save

ESC: Exit

F1: General Help

F5: Previous Values

F6: Fail-Safe Defaults

 

F7: Optimized Defaults

On-Chip Primary PCI IDE

Enabled

Enable onboard 1st channel IDE port. (Default value)

Disabled

Disable onboard 1st channel IDE port.

On-Chip SATA Mode

Disabled

Disable this function.

Auto

BIOS will auto detect. (Default value)

Combined

Set On-Chip SATA mode to Combined, you can use up to 4 HDDs on

 

the motherboard; 2 for SATA and the other for PATA.

Enhanced

Set On-Chip SATA mode to Enhanced, the motherboard allows up to 6

 

HDDs to use; 4 SATA HDDs plus PATA HDDs.

Non-Combined

Set On-Chip SATA mode to Non-Combined, SATA will be simulated to

 

PATA mode. Support a maximum of 4 SATA devices. PATA devices will be

 

ignored.

PATA IDE Set to

Ch.1

Master/Slave

Set PATA IDE to Ch. 1 Master/Slave.

Ch.0

Master/Slave

Set PATA IDE to Ch. 0 Master/Slave. (Default value)

SATA Port 0 Set to

This value will auto make by the setting "On-Chip SATA Mode" and "PATA IDE Set to".

If PATA IDE were set to Ch. 1 Master/Slave, this function will auto set to Ch. 0 Master/Slave.

SATA Port 1 Set to

This value will auto make by the setting "On-Chip SATA Mode" and "PATA IDE Set to".

If PATA IDE were set to Ch. 0 Master/Slave, this function will auto set to Ch. 1 Master/Slave.

USB Controller

Enabled

Enable USB Controller. (Default value)

Disabled

Disable USB Controller.

GA-8I915MD-G/GA-8I915MD-GV Motherboard - 38 -

Image 38
Contents GA-8I915MD-G/ GA-8I915MD-GV Motherboard GA-8I915MD-GV Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-8I915MD-G / GA-8I915MD-GV Motherboard Layout Block Diagram GA-8I915MD-G Block Diagram GA-8I915MD-GV Page Instances of Non-Warranty Considerations Prior to InstallationInstallation Notices Preparing Your ComputerFeature Summary CPUUse of licensed Award Bios Installation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards Graphics Card Support ListGV-NX68T256DH I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD Floppy ConnectorIDE1 IDE Connector SATA0/SATA1 Sata ConnectorFaudio Front Audio Panel Connector Pwrled OptionalFpanel Front Panel Jumper Cdin CDAuxin AUX In Connector Spdifio Spdif In/Out15 F1USB / F2USB Front USB Connectors SurcenComb Comb Connector CI Chassis Intrusion, Case OpenBATBattery Clrcmos Clear CmosStatus Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. GA-8I915MD-G F3a „ Save & Exit Setup „ Set Supervisor Password„ Set User Password „ Exit Without SavingIDE Channel 0 Master, Slave Standard Cmos FeaturesTime IDE Channel 2/3 MasterHalt on Floppy 3 Mode Support for Japan AreaDrive a / Drive B MemoryFirst / Second / Third Boot Device Advanced Bios FeaturesHard Disk Boot Priority Password CheckNo-Execute Memory Protect Note CPU Hyper-ThreadingLimit Cpuid Max. to CPU Enhanced Halt C1E NoteIntegrated Peripherals USB 2.0 Controller OnBoard LAN Boot ROMParallel Port Mode USB Keyboard SupportResume by Alarm Power Management SetupECP Mode Use DMA Power On By MouseKB Power on Password PnP/PCI ConfigurationsPower On By Keyboard AC Back FunctionPC Health Status CPU Smart FAN Mode CPU Smart FAN Control NoteMemory Frequency For Frequency/Voltage ControlCPU Clock RatioNote Memory Frequency MhzLoad Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Drivers Installation Install Chipset DriversSoftware Applications Driver CD InformationHardware Information Contact UsEnglish Unique Software Utilities EasyTune 5 Introduction User Interface OverviewSystem requirements Xpress Recovery2 IntroductionHow to use the Xpress Recovery2 Limitations Main Screen of Xpress Recovery2Precautions Before You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Entering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen EnglishCongratulation!! You have updated Bios successfully Bios file becomes F4 after updatingMethod 2 @BIOSTM Utility Methods and stepsEnglish Channel Audio Setup 4 2 / 4 / 6 Channel Audio Function IntroductionChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode NotesEnglish Basic & Advanced 6 Channel Analog Audio Output Mode Notes Spdif Output Device Optional Device Troubleshooting English GA-8I915MD-G/GA-8I915MD-GV Motherboard English English English English Contact Us Taiwan HeadquartersChina Shanghai