Gigabyte GA-8I915MD-GV user manual Block Diagram GA-8I915MD-G

Page 8

Block Diagram (GA-8I915MD-G)

PCI-ECLK (100MHz)

PCI Express x16

VGA

PCI Bus

RTL8110S

RJ45

3 PCI

PCICLK (33MHz)

LGA775					CPUCLK+/-(200/133MHz)
LGA775
Processor

	Host
	Host
	Interface				DDRII 600(Note)/533/400MHz DIMM
Intel					DDRII 600(Note)/533/400MHz DIMM

								Dual Channel Memory
915G
915G
MCH

MCHCLK (200/133MHz)

66MHz

33MHz

14.318MHz

48MHz

BIOS

Intel						2 Serial ATA
						ATA33/66/100
ICH6						IDE1 Channel

Floppy

LPT Port

IT8712

COM Ports

CODEC

24MHz

8

USB

33MHz

Ports

MIC Line-Out Line-In

PS/2 KB/Mouse

(Note) To use a DDRII 600 memory module on the motherboard, you must install an 800MHz FSB processor and overclock in BIOS.

- 8 -

Image 8

Contents GA-8I915MD-G/ GA-8I915MD-GV Motherboard GA-8I915MD-GV Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-8I915MD-G / GA-8I915MD-GV Motherboard Layout Block Diagram GA-8I915MD-G Block Diagram GA-8I915MD-GV Page Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary CPUUse of licensed Award Bios Installation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards Graphics Card Support ListGV-NX68T256DH I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD Floppy ConnectorIDE1 IDE Connector SATA0/SATA1 Sata ConnectorFaudio Front Audio Panel Connector Pwrled OptionalFpanel Front Panel Jumper Cdin CDAuxin AUX In Connector Spdifio Spdif In/Out15 F1USB / F2USB Front USB Connectors SurcenComb Comb Connector CI Chassis Intrusion, Case OpenBATBattery Clrcmos Clear CmosStatus Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. GA-8I915MD-G F3a „ Set Supervisor Password „ Set User Password„ Save & Exit Setup „ Exit Without SavingStandard Cmos Features TimeIDE Channel 0 Master, Slave IDE Channel 2/3 MasterFloppy 3 Mode Support for Japan Area Drive a / Drive BHalt on MemoryAdvanced Bios Features Hard Disk Boot PriorityFirst / Second / Third Boot Device Password CheckCPU Hyper-Threading Limit Cpuid Max. toNo-Execute Memory Protect Note CPU Enhanced Halt C1E NoteIntegrated Peripherals OnBoard LAN Boot ROM Parallel Port ModeUSB 2.0 Controller USB Keyboard SupportPower Management Setup ECP Mode Use DMAResume by Alarm Power On By MousePnP/PCI Configurations Power On By KeyboardKB Power on Password AC Back FunctionPC Health Status CPU Smart FAN Mode CPU Smart FAN Control NoteFrequency/Voltage Control CPU Clock RatioNoteMemory Frequency For Memory Frequency MhzLoad Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Drivers Installation Install Chipset DriversSoftware Applications Driver CD InformationHardware Information Contact UsEnglish Unique Software Utilities EasyTune 5 Introduction User Interface OverviewSystem requirements Xpress Recovery2 IntroductionHow to use the Xpress Recovery2 Limitations Main Screen of Xpress Recovery2Precautions Before You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen EnglishCongratulation!! You have updated Bios successfully Bios file becomes F4 after updatingMethod 2 @BIOSTM Utility Methods and stepsEnglish Channel Audio Setup 4 2 / 4 / 6 Channel Audio Function IntroductionChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode NotesEnglish Basic & Advanced 6 Channel Analog Audio Output Mode Notes Spdif Output Device Optional Device Troubleshooting English GA-8I915MD-G/GA-8I915MD-GV Motherboard English English English English Contact Us Taiwan HeadquartersChina Shanghai