Gigabyte GA-8I845GE775-G Integrated Peripherals, On-Chip Secondary PCI IDE, IDE1 Conductor Cable

Page 34

Integrated Peripherals

English

2-3	Integrated Peripherals

		CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
				Integrated Peripherals
	On-Chip Primary PCI IDE			[Enabled]		Item Help
	On-Chip Secondary PCI IDE			[Enabled]		Menu Level `
	IDE1 Conductor Cable			[Auto]
	IDE2 Conductor Cable			[Auto]		If a hard disk
	USB Controller			[Enabled]		controller card is
	USB Keyboard Support			[Disabled]		used, set at Disabled
	USB Mouse Support			[Disabled]
	AC97 Audio			[Auto]		[Enabled]
	Onboard H/W LAN			[Enabled]		Enable onboard IDE
	Onboard LAN Boot ROM			[Disabled]		PORT
	Onboard Serial Port 1			[3F8/IRQ4]
	Onboard Serial Port 2			[2F8/IRQ3]		[Disabled]
	Onboard Parallel Port			[378/IRQ7]		Disable onboard IDE
	Parallel Port Mode			[SPP]		PORT
x ECP Mode Use DMA				3
KLJI: Move		Enter: Select		+/-/PU/PD: Value	F10: Save	ESC: Exit	F1: General Help
	F5: Previous Values			F6: Fail-Safe Defaults		F7: Optimized Defaults

	On-Chip Primary PCI IDE
	Enabled		Enable onboard 1st channel IDE port. (Default value)
	Disabled		Disable onboard 1st channel IDE port.
	On-Chip Secondary PCI IDE
	Enabled		Enable onboard 2nd channel IDE port. (Default value)
	Disabled		Disable onboard 2nd channel IDE port.
	IDE1 Conductor Cable
	Auto		BIOS autodetects IDE1 conductor cable .(Default Value)
	ATA66/100		Set IDE1 Conductor Cable to ATA66/100 (please make sure your IDE
			device and cable are compatible with ATA66/100).
	ATA33		Set IDE1 Conductor Cable to ATA33. (Please make sure your IDE
			device and cable are compatible with ATA33)
	IDE2 Conductor Cable
	Auto		BIOS autodetects IDE2 conductor cable. (Default Value)
	ATA66/100		Set IDE2 Conductor Cable to ATA66/100(please make sure your IDE
			device and cable are compatible with ATA66/100)
	ATA33		Set IDE2 Conductor Cable to ATA33. (Please make sure your IDE
			device and cable are compatible with ATA33)
	USB Controller
	Enabled		Enable USB Controller. (Default value)
	Disabled		Disable USB Controller.
	USB Keyboard Support
	Enabled		Enable USB Keyboard Support.
	Disabled		Disable USB Keyboard Support. (Default value)

GA-8I845GE775-G Motherboard

- 34 -

Image 34

Contents Intel Pentium 4 LGA775 Processor Motherboard GA-8I845GE775-GUsers Manual Rev. 1001 12ME-I845GETG-1001Motherboard MotherboardGA-8I845GE775-G April 22 GA-8I845GE775-GCopyright Product Manual ClassificationTable of Contents 4-1-1 Chapter 3 Drivers InstallationChapter 4 Appendix 4-1-2GA-8I845GE775-G Motherboard Layout Block Diagram Page Installation Notices Chapter 1Hardware Installation1-1 Considerations Prior to Installation Instances of Non-Warranty1-2 Feature Summary BIOS 1-3 Installation of the CPU and Heatsink 1-3-1 Installation of the CPU1-3-2 Installation of the Heatsink 1-4 Installation of Memory notch DDR memory module1-5 Installation of Expansion Cards Parallel Port PS/2 Keyboard and PS/2 Mouse Connector1-6 I/O Back Panel Introduction Serial Port COMA1-7 Connectors Introduction 111 2010 1/2 ATX12V / ATX Power ConnectorPin No 5 FDD FDD Connector 3/4 CPUFAN / SYSFANCooler Fan Power ConnectorSYSFAN CD-L 6 IDE1/2 IDE Connector7 CDIN CD In Connector CD-RPower 8 FPANEL Front Panel JumperReset Switch IDE Hard Disk Active LED 10 SPDIFIO SPDIF In/ Out 9 FAUDIO Front Audio Panel ConnectorRear Audio R/ Return R 11 SURCEN Surround Center Connector 12 F USB1 Front USB Connector13 COMB COMB Connector 14 CI Chassis Intrusion, Case Open16 BATBattery 15 CLRCMOS Clear CMOSEnglish CONTROL KEYS Chapter 2 BIOS SetupStatus Page Setup Menu / Option Page Setup Menu Main Menu„ Advanced BIOS Features The Main Menu Example BIOS Version F1„ Standard CMOS Features „ Power Management Setup„ Save & Exit Setup „ Set Supervisor Password„ Set User Password „ Exit Without SavingTime Standard CMOS FeaturesDate IDE Primary Master, Slave /IDE Secondary Master, SlaveHalt on Drive A / Drive BFloppy 3 Mode Support for Japan Area MemoryFirst / Second / Third Boot Device Advanced BIOS FeaturesBoot Up Floppy Seek Limit CPUID Max. to Password CheckCPU Hyper-Threading No-Execute Memory ProtectNoteIDE1 Conductor Cable Integrated PeripheralsOn-Chip Secondary PCI IDE IDE2 Conductor CableAC97 Audio Onboard LAN Boot ROMUSB Mouse Support Onboard H/W LANResume by Alarm Power Management SetupPower LED in S1 State ACPI Suspend TypeKB Power ON Password Power On By MousePower On By Keyboard AC BACK FunctionPCI2 IRQ Assignment PnP/PCI ConfigurationsPCI1/5 IRQ Assignment PCI3 IRQ AssignmentCurrent VoltageV Vcore / DDR25V / +3.3V / +12V PC Health StatusCase Opened Current CPU TemperatureCPU Host Clock Control Frequency/Voltage ControlCPU Clock Ratio CPU Host Frequency MhzMemory Frequency Mhz Top PerformanceHost/DRAM Clock ratio PCI/AGP Frequency MhzLoad Fail-Safe Defaults 2-10 Load Optimized DefaultsSet Supervisor/User Password 2-112-12 Save & Exit Setup 2-13 Exit Without SavingChapter 3Drivers Installation 3-1 Install Chipset Drivers3-2 Software Application 3-3 Software InformationThis page lists all device you have for this motherboard 3-4 Hardware Information3-5 Contact Us Please see the last page for detailsEnglish How to use the Xpress Recovery 4-1-1 Xpress Recovery IntroductionWhat is Xpress Recovery ? Chapter 4 AppendixF9 For Xpress Recovery Intel 865PE AGPSet BIOS for 8IPE1000MT F1 Check System Health OK2. Execute Restore Utility 1. Execute Backup Utility Press B to Backup your System or Esc to Exit This program will recover your system to factory defaultMethod 1 Q-FlashTM Utility 4-1-2 Flash BIOS Method IntroductionUpdating BIOS with Q-FlashTM Utility on Dual BIOS Motherboards Before You BeginEntering the Q-FlashTM utility Exploring the Q-FlashTM / Dual BIOS utility screenTask menu for Dual BIOS utility Task menu for Q-Flash utilitydisk Using the Q-FlashTM utilitySteps stageBIOS, too 3. Press Y button on your keyboard after you are sure to update BIOSPlease do not take out the floppy disk when it begins flashing BIOS The BIOS file becomes Fba after updatingPart Two Updating BIOS with Q-FlashTM Utility on Single-BIOS MotherboardsPress Y on your keyboard to save and exit Exploring the Q-FlashTM utility screen Are you sure to RESET ? Congratulation!! You have updated BIOS successfullyCopy BIOS completed - Pass at this stageMethod 2 @BIOSTM Utility 1. Methods and steps2. Note Stereo Speakers Connection and Settings 4-1-3 2- / 4- / 6-/ 8- Channel Audio Function Introduction4 Channel Audio Setup 6 Channel Audio Setup Mic In Center/Subwoofer Speaker Out8 Channel Audio Setup requires Audio Combo Kit, optional device Surround-Kit connector SPDIF cable connectorEnglish SPDIF Output Device Optional Device Note1UAJ Introduction Enable UAJ functionYou can click UAJ Automatic button to enable UAJ function 4-2 Troubleshooting 10 beeps CMOS shutdown register read/write errorEnglish AppendixEnglish TEL +886-2-8912-4888 Contact UsAddress No.6, Bau Chiang Road, Hsin-Tien, Taipei 231, Taiwan G.B.T. INC TEL+1-626-854-9338China