Gigabyte GA-K8VT890-9 Drive a / Drive B, Floppy 3 Mode Support for Japan Area, Halt on, Memory

Page 33

Hard drive information should be labeled on the outside drive casing. Enter the appropriate option based on this information.

Cylinder

Number of cylinders

Head

Number of heads

Precomp

Write precomp

Landing Zone

Landing zone

Sector

Number of sectors

Drive A / Drive B

The category identifies the types of floppy disk drive A or drive B that has been installed in the computer.

None

No floppy drive installed

360K, 5.25"

5.25 inch PC-type standard drive; 360K byte capacity.

1.2M, 5.25"

5.25 inch AT-type high-density drive; 1.2M byte capacity

 

(3.5 inch when 3 Mode is Enabled).

720K, 3.5"

3.5 inch double-sided drive; 720K byte capacity

1.44M, 3.5"

3.5 inch double-sided drive; 1.44M byte capacity.

2.88M, 3.5"

3.5 inch double-sided drive; 2.88M byte capacity.

Floppy 3 Mode Support (for Japan Area)

Disabled

Normal Floppy Drive. (Default value)

Drive A

Drive A is 3 mode Floppy Drive.

Drive B

Drive B is 3 mode Floppy Drive.

Both

Drive A & B are 3 mode Floppy Drives.

Halt on

The category determines whether the computer will stop if an error is detected during power up.

No Errors

The system boot will not stop for any error that may be detected and you

 

will be prompted.

All Errors

Whenever the BIOS detects a non-fatal error the system will be stopped.

All, But Keyboard

The system boot will not stop for a keyboard error; it will stop for all other

 

errors. (Default value)

All, But Diskette

The system boot will not stop for a disk error; it will stop for all other errors.

All, But Disk/Key

The system boot will not stop for a keyboard or disk error; it will stop for all

 

other errors.

Memory

The category is display-only which is determined by POST (Power On Self Test) of the BIOS.

Base Memory

The POST of the BIOS will determine the amount of base (or conventional) memory installed in the system.

The value of the base memory is typically 512K for systems with 512K memory installed on the motherboard, or 640K for systems with 640K or more memory installed on the motherboard.

Extended Memory

The BIOS determines how much extended memory is present during the POST.

This is the amount of memory located above 1 MB in the CPU's memory address map.

Total Memory

This item displays the memory size that used.

English

- 33 -

BIOS Setup

Image 33
Contents GA-K8VT890-9 Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation GA-K8VT890-9 Motherboard Layout Block Diagram Page Installation Notices Considerations Prior to InstallationInstances of Non-Warranty Preparing Your ComputerALC850 Codec UAJ Feature SummaryBios Installation of the CPU Installation of the CPU and Fan Heat SinkInstallation of the Fan Heat Sink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATA0 / SATA1 Serial ATA Connectors IDE1 / IDE2 IDE ConnectorPwrled Fpanel Front Panel Jumper Cdin CD In Connector Faudio Front Audio Panel ConnectorSpdifio Spdif In / Out Connector Surcen Surround Center ConnectorClrcmos Clear Cmos USB1 / FUSB2 Front USB ConnectorCI Chassis Intrusion, Case Open English Main Menu Status Page Setup Menu / Option Page Setup Menu Main Menu For example Bios Ver. D2 „ Load Optimized Defaults „ Load Fail-Safe Defaults„ Set Supervisor Password „ Set User PasswordTime Standard Cmos FeaturesIDE Channel 0 Master/Slave IDE Channel 1 Master/Slave IDE Channel 2/3 MasterDrive a / Drive B Floppy 3 Mode Support for Japan AreaHalt on MemoryHard Disk Boot Priority Advanced Bios FeaturesFirst / Second / Third Boot Device Password CheckRAID Integrated PeripheralsUSB 2.0 Controller Parallel Port ModeUSB Keyboard Support USB Mouse SupportAcpi Suspend Type Power Management SetupResume by Alarm PME/PCIE Event Wake UpModem Ring Resume PCI 1 IRQ Assignment PnP/PCI ConfigurationsPC Health Status Frequency/Voltage Control Top Performance Load Fail-Safe DefaultsSet Supervisor/User Password Load Optimized DefaultsExit Without Saving Save & Exit SetupInstall Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish Unique Software Utilities EasyTune 5 IntroductionUser Interface Overview Xpress Recovery Introduction What is Xpress Recovery ?How to use the Xpress Recovery F9 For Xpress Recovery Exit and Restart Remove Backup Image  Remove backup image. Are you sure? Y/NFlash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Task menu for Dual Bios utility Exploring the Q-FlashTM / Dual Bios utility screenEntering the Q-FlashTMutility Task menu for Q-Flash utilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two English Exploring the Q-FlashTMutility screenBios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish RAID Levels Serial ATA Bios Setting Utility IntroductionEntering the VT8237VT8237R Sata RAID Bios Setup Utility Configuring the VT8237VT8237R Sata RAID BiosCreate Array 111.79 Stripe0 SerialCh1 Master ST3120026AS Delete Array Serial Number View Cd bootdrv Menu Installing the RAID drivers5 2- / 4- / 6- / 8- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English English English Spdif Output Device Optional Device Introduction of audio connectors Jack-Sensing and UAJ IntroductionAuto-detecting Manual setting Enable UAJ functionUAJ Introduction AMI Bios Beep Codes TroubleshootingEnglish Taiwan Headquarters Contact UsChina Shanghai