Gigabyte GA-K8VT890-9 user manual Xpress Recovery Introduction, What is Xpress Recovery ?

Page 50

English

4-1-2 Xpress Recovery Introduction

What is Xpress Recovery ?

Xpress Recovery is a utility used to back up and restore an OS partition. If the hard drive is not working properly, the user can restore the drive to its original state.

1.Supports FAT16, FAT32, and NTFS formats

2. Must be connected to the IDE1 Master

3. Allows installation of only one OS

4.Must be used with an IDE hard disk supporting HPA

5.The first partition must be set as the boot partition. When the boot partition is backed up, please do not alter its size.

6.Xpress Recovery is recommended when using Ghost to return boot manager to NTFS format.

How to use the Xpress Recovery

1.Boot from CD-ROM (BMP Mode)

Enter the BIOS menu, select "Advanced BIOS Feature" and set to boot from CD-ROM. Insert the provided driver CD into your CD drive, then save and exit the BIOS menu. Once the computer has restarted, the phrase "Boot from CD:" will appear at the bottom left-hand corner of the screen. When "Boot from CD:" appears, press any key to enter Xpress Recovery.

Once you have completed this step, subsequent access to Xpress Recovery can also function by pressing the F9 key during computer power on.

.

 

.

 

Verifying DMI Pool Data

Boot from CD:

Boot from CD:

Xpress Recovery V1.0 (C) Copy Right 2003. GIGABYTE Technology CO. , Ltd.

1.Execute Backup Utility

2.Execute Restore Utility

3.Remove Backup Image

4.Set Password

5.Exit and Restart

Build 2011

GA-K8VT890-9 Motherboard

- 50 -

Image 50
Contents GA-K8VT890-9 Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-K8VT890-9 Motherboard Layout Block Diagram Page Instances of Non-Warranty Considerations Prior to InstallationInstallation Notices Preparing Your ComputerFeature Summary ALC850 Codec UAJBios Installation of the CPU and Fan Heat Sink Installation of the CPUInstallation of the Fan Heat Sink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector SATA0 / SATA1 Serial ATA ConnectorsPwrled Fpanel Front Panel Jumper Faudio Front Audio Panel Connector Cdin CD In ConnectorSurcen Surround Center Connector Spdifio Spdif In / Out ConnectorUSB1 / FUSB2 Front USB Connector Clrcmos Clear CmosCI Chassis Intrusion, Case Open English Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. D2 „ Set Supervisor Password „ Load Fail-Safe Defaults„ Load Optimized Defaults „ Set User PasswordIDE Channel 0 Master/Slave IDE Channel 1 Master/Slave Standard Cmos FeaturesTime IDE Channel 2/3 MasterHalt on Floppy 3 Mode Support for Japan AreaDrive a / Drive B MemoryFirst / Second / Third Boot Device Advanced Bios FeaturesHard Disk Boot Priority Password CheckIntegrated Peripherals RAIDUSB Keyboard Support Parallel Port ModeUSB 2.0 Controller USB Mouse SupportPower Management Setup Acpi Suspend TypeModem Ring Resume Resume by AlarmPME/PCIE Event Wake Up PnP/PCI Configurations PCI 1 IRQ AssignmentPC Health Status Frequency/Voltage Control Load Fail-Safe Defaults Top PerformanceLoad Optimized Defaults Set Supervisor/User PasswordSave & Exit Setup Exit Without SavingDrivers Installation Install Chipset DriversSoftware Application Software Information Hardware Information Contact UsEnglish User Interface Overview Unique Software UtilitiesEasyTune 5 Introduction How to use the Xpress Recovery Xpress Recovery IntroductionWhat is Xpress Recovery ? F9 For Xpress Recovery Remove Backup Image  Remove backup image. Are you sure? Y/N Exit and RestartBefore You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Entering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen EnglishCongratulation!! You have updated Bios successfully Bios file becomes F4 after updatingMethod 2 @BIOSTM Utility Methods and stepsEnglish Serial ATA Bios Setting Utility Introduction RAID LevelsConfiguring the VT8237VT8237R Sata RAID Bios Entering the VT8237VT8237R Sata RAID Bios Setup UtilityCreate Array 111.79 Stripe0 SerialCh1 Master ST3120026AS Delete Array Serial Number View Installing the RAID drivers Cd bootdrv MenuStereo Speakers Connection and Settings 5 2- / 4- / 6- / 8- Channel Audio Function IntroductionChannel Audio Setup English English English Spdif Output Device Optional Device Auto-detecting Introduction of audio connectorsJack-Sensing and UAJ Introduction UAJ Introduction Manual settingEnable UAJ function Troubleshooting AMI Bios Beep CodesEnglish Contact Us Taiwan HeadquartersChina Shanghai