Gigabyte GA-K8VT890-9 user manual Integrated Peripherals, Raid

Page 35

2-3	Integrated Peripherals

			CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
				Integrated Peripherals
	IDE DMA transfer access			[Enabled]		Item Help
	OnChip IDE Channel0			[Enabled]		Menu Level`
	OnChip IDE Channel1			[Enabled]
	OnChip Serial ATA			[Enabled]
	SATA Mode			[RAID]
	AC97 Audio			[Auto]
	Onboard H/W LAN			[Enabled]
	USB 1.1 Controller			[Enabled]
	USB 2.0 Controller			[Enabled]
	USB Keyboard Support			[Disabled]
	USB Mouse Support			[Disabled]
	Onboard Serial Port 1			[3F8/IRQ4]
	Onboard Serial Port 2			[2F8/IRQ3]
	Onboard Parallel Port			[378/IRQ7]
	Parallel Port Mode			[SPP]
	Midi Port Address			[Disabled]
x	Midi Port IRQ			10
KLJI: Move		Enter: Select		+/-/PU/PD: Value	F10: Save	ESC: Exit	F1: General Help
	F5: Previous Values			F6: Fail-Safe Defaults		F7: Optimized Defaults

	IDE DMA transfer access
	Enabled		Enable IDE DMA transfer access. (Default value)
	Disabled		Disable this function.
	OnChip IDE Channel0
	Enabled		Enable onboard 1st channel IDE port. (Default value)
	Disabled		Disable onboard 1st channel IDE port.
	OnChip IDE Channel1
	Enabled		Enable onboard 2nd channel IDE port. (Default value)
	Disabled		Disable onboard 2nd channel IDE port.
	OnChip Serial ATA
	Enabled		Enable onboard Serial ATA function. (Default value)
	Disabled		Disable onboard Serial ATA function.
	SATA Mode
	RAID		Set onboard Serial ATA function as RAID. (Default value)
	IDE		Set onboard Serial ATA function as IDE.
	AC97 Audio
	Auto		Auto detect onboard AC97 audio function. (Default value)
	Disabled		Disable onboard AC97 audio function.
	Onboard H/W LAN
	Enabled		Enable onboard H/W LAN function. (Default value)
	Disabled		Disable this function.
	USB 1.1 Controller
	Enabled		Enable USB 1.1 controller. (Default value)
	Disabled		Disable USB 1.1 controller.

English

- 35 -

BIOS Setup

Image 35

Contents GA-K8VT890-9 Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation GA-K8VT890-9 Motherboard Layout Block Diagram Page Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantyALC850 Codec UAJ Feature SummaryBios Installation of the CPU Installation of the CPU and Fan Heat SinkInstallation of the Fan Heat Sink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATA0 / SATA1 Serial ATA Connectors IDE1 / IDE2 IDE ConnectorPwrled Fpanel Front Panel Jumper Cdin CD In Connector Faudio Front Audio Panel ConnectorSpdifio Spdif In / Out Connector Surcen Surround Center ConnectorClrcmos Clear Cmos USB1 / FUSB2 Front USB ConnectorCI Chassis Intrusion, Case Open English Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. D2 „ Set User Password „ Load Fail-Safe Defaults„ Load Optimized Defaults „ Set Supervisor Password IDE Channel 2/3 Master Standard Cmos Features Time IDE Channel 0 Master/Slave IDE Channel 1 Master/SlaveMemory Floppy 3 Mode Support for Japan AreaDrive a / Drive B Halt onPassword Check Advanced Bios FeaturesHard Disk Boot Priority First / Second / Third Boot DeviceRAID Integrated PeripheralsUSB Mouse Support Parallel Port ModeUSB 2.0 Controller USB Keyboard SupportAcpi Suspend Type Power Management SetupModem Ring Resume Resume by AlarmPME/PCIE Event Wake Up PCI 1 IRQ Assignment PnP/PCI ConfigurationsPC Health Status Frequency/Voltage Control Top Performance Load Fail-Safe DefaultsSet Supervisor/User Password Load Optimized DefaultsExit Without Saving Save & Exit SetupInstall Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish User Interface Overview Unique Software UtilitiesEasyTune 5 Introduction How to use the Xpress Recovery Xpress Recovery IntroductionWhat is Xpress Recovery ? F9 For Xpress Recovery Exit and Restart Remove Backup Image Remove backup image. Are you sure? Y/NBefore You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Task menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two English Exploring the Q-FlashTMutility screenBios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish RAID Levels Serial ATA Bios Setting Utility IntroductionEntering the VT8237VT8237R Sata RAID Bios Setup Utility Configuring the VT8237VT8237R Sata RAID BiosCreate Array 111.79 Stripe0 SerialCh1 Master ST3120026AS Delete Array Serial Number View Cd bootdrv Menu Installing the RAID drivers5 2- / 4- / 6- / 8- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English English English Spdif Output Device Optional Device Auto-detecting Introduction of audio connectorsJack-Sensing and UAJ Introduction UAJ Introduction Manual settingEnable UAJ function AMI Bios Beep Codes TroubleshootingEnglish Taiwan Headquarters Contact UsChina Shanghai