ATTO Technology FC-44ES, FC-42XS, FC-41XS, FC-42ES operation manual

Page 27

Adding a Celerity FC adapter to an existing Windows installation

Note

Complete this installation procedure before attaching any devices to the adapter.

1Complete the steps in Upgrading your existing Celerity FC driver on page 21 to pre-install the driver.

2Shutdown Windows when Setup prompts you to do so.

3Install your new Celerity FC adapter into an available PCI expansion slot.

4Restart Windows. During the boot process, Windows detects your Celerity FC adapter and the Found New Hardware Wizard is displayed.

5Use the default settings for each adapter channel.

6Insert the Celerity FC Installation disk when asked to do so.

7When adapter installation is complete, the Found New Hardware Wizard displays an ATTO Phantom Device for each channel. Use the wizard default settings to complete the installation.

8Shut down the system and set up the final adapter configuration.

a.If the Celerity FC adapter is replacing another adapter in the system, disconnect the FC cables from the adapter and remove the adapter from the system, or you can move the Celerity FC adapter to the PCI slot that the previous adapter occupied if this slot is more suitable for the Celerity FC adapter.

b.Attach the appropriate FC cables to the Celerity FC adapter.

c.Close the computer chassis, turn on the power and restart Windows.

Note

If you moved the adapter to a different PCI slot, the Found New Hardware Wizard displays. Proceed through the wizard with

the default settings for each adapter channel to complete the installation.

Install a fresh copy of the Windows OS onto a disk attached to the Celerity FC adapter

Note

The Celerity FC driver does not support boot functionality on Itanium systems; therefore, the procedure described below does not apply to Windows Server 2003 for Itanium systems.

1Start Windows text mode setup as per the instructions provided with Windows.

2Press F6 when the first blue window, called Windows Setup, displays.

The setup program displays a prompt in the status window on the bottom left of the monitor. Setup continues to load files after you press F6.

3A new window displays instructions to specify additional mass storage devices. Press S indicating that you wish to install a storage device.

4Insert the Celerity FC installation diskette in drive A: and press Enter.

5A screen displays a list of Celerity FC adapters. Select your adapter and press Enter.

6Windows Setup loads the files from the floppy and then displays the screen described in step 2. The ATTO Celerity FC device should now be listed as detected.

7Repeat steps 2 - 4 for any other vendor- supplied driver installation disks.

8After all other drivers have been processed, press Enter and proceed with the rest of the Windows Installation procedure.

Note

When Windows begins copying files to your hard disk, a display prompts you to insert the Celerity FC installation disk and any other vendor-supplied disks you used during custom installation. This is normal. The first time you inserted the disks, Windows only loaded the drivers into memory; the second time you insert the disk(s), Windows is copying the driver to your hard disk.

22

Image 27
Contents Celerity FC Storage Adapters Page Page Contents Fibre Channel is a key technology for storage Hardware installationConfiguring and updating drivers Updating hardware flash TroubleshootingCelerity FC-42ES Adapter Atto provides Fibre Channel solutionsCelerity FC-44ES Adapter Software specificationsCelerity FC-42XS Adapter PCI bus specificationsCelerity FC-41XS Adapter Celerity FC-21PS Adapter Celerity FC-22XH Celerity FC-24XL Iopc specificationsFeatures Celerity Selection GuideCelerity FC Storage Adapters Product Fibre Channel is a key technology for storage GlossaryTerm Definition LED Fibre Channel address Hardware installationInstallation System requirementsFC-42ES Adapter FC-44ES Adapter FC-42XS Adapter FC-41XS Adapter SFP LC optical ConnectorFC-21PS Adapter SFF duplex LC optical connector FC controllerOn-board hub FC-22XH Storage AdapterSFP LC optical Connectors PCI-X connector FC-24XL Advanced Storage AdapterFC controllers Page Upgrading your existing Celerity FC driver Configuring and updating driversInitial configuration Windows 2000/XP/ServerPage Mac OS X driver installation, update Linux driver installation, updateNew or previous installation Updating hardware flash To update hardware flash in all operating systemsLaunch the Configuration Tool To update hardware flash on a PC using the Bios utilitiesGeneral suggestions TroubleshootingIf devices are not accessible Mac OSLinux Select PropertiesSelect Device Manager European standards Appendix a Standards and compliancesFCC standards radio and television interference Canadian standardsUsage restrictions Optical Cables Appendix B AccessoriesFibre Channel and iSCSI solutions Scsi solutionsAppendix C Scsi adapter selection guide Ultra Product FeaturesAppendix D Contact Atto Technology, Inc
Related manuals
Manual 37 pages 25.13 Kb