Teac AG-H380 System Connection, Speaker Connections, Subwoofer OUT jack, How to connect

Page 9

GSpeaker Connections

AG-H380’s red speaker terminals are the + (positive) terminals and the black terminals are the _(negative) terminals.

The + side of the speaker cable is marked to make it distinguishable from the negative side of the cable. Connect this marked side to the red + terminal and the unmarked side to the black _terminal of AG-H380 and speakers.

CAUTION

<To avoid damaging the speakers by a sudden high-level signal, be sure to switch the power off before connecting the speakers.

<Check the impedance of your speakers. Connect speaker with an impedance of 6 ohms or more.

<Prepare the speaker cords for connection by stripping off approximately 10 mm or less (no more as this could cause a short-circuit) of the outer insulation. Twist the wires tightly together to avoid tangles:

How to connect

1.Turn the terminal cap counter-clockwise to loosen it. The speaker terminal caps cannot be fully removed from the base.

2.Insert the wire into the terminal fully and turn the terminal cap clockwise to securely connect it:

3. Make sure it is fastened firmly by pulling the cable lightly.

For European customers

In accordance with European safety regulations, it is not possible to connect banana plugs into the speaker terminals on European models.

The holes into which banana plugs are inserted have been covered with black caps. Connect the speakers using spades or bare wires.

If the black caps become separated from the terminals, return them to their original position.

HSUBWOOFER OUT jack

Connect a commercially available powered subwoofer.

System Connection

If you have TEAC Reference 380 series, convenient system control operations and AI direct play functions are possible.

< By pressing the POWER switch of AG-H380, you can switch ON/ standby all the unit connected by remote control cords.

(Set the REMOTE CONTROL SELECTOR on the rear panel of the PD-H380 to “SYSTEM”.)

< When you press the PLAY button of PD-H380, the source of

AG-H380 is set to “CD” automatically.

 

< When you select “CD” by pressing the SOURCE button of

 

AG-H380, PD-H380 starts playback automatically.

 

< When you turn on the system, the source that was selected last

 

time will start playback automatically.

ENGLISH

< You can use the system remote control unit to operate all the

 

unit connected by remote control cords.

 

Connect the REMOTE CONTROL jack of each component by remote control connection cords.

REMOTE

CONTROL

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents AG-H380 Important Safety Instructions Page Contents Before UseMP3 and WMA AM Indoor Loop Antenna Connecting Antennas AM/FMFM Indoor Antenna FM Outdoor AntennaTurntable ConnectionsDVD player, etc PD-H380AUX 1/AUX 2/CD jacks AC Power CordPhono jacks USB portSubwoofer Speaker ConnectionsSystem Connection How to connectSpeaker Connections Subwoofer OUT jackName of Each Control FM Mode TimerVolume STANDBY/ONBattery Installation Remote Control UnitBattery Replacement Precautions Concerning BatteriesHow to select source How to turn the unit on or offAdjust the volume Listening through headphonesHow to adjust the bass and treble sound Listening to iPodTo pause playback Search for a part of a song To skip to the next or a previous songTo go back to the previous menu Select the menu itemDirect Mode default Changing the display modeExtended mode Listening to an USB DeviceSearch To pause playback pause modeTo stop playback To skip to the next or a previous songShuffle Playback USB Repeat Playback USBRepeat one file RPT Repeat all the songs RPT AllProgrammed Playback USB Press the Program button in the stop modePress the ˙ or ¥ button to select a file Within 5 seconds, press the Program buttonTo check the programmed order To add a file to the programmeTo delete a file from the programme To clear the programme Before Recording Display USBRecording to USB Deleting a file from USBWithin 3 seconds, press the Clear button Listening to FM/AM FM ModePreset Tuning Manual Preset AM/FMPresetting Automatically Tune in an FM station see Press the RDS button PTY SearchNews Alarm Test Alarm-AlarmCurrent Affairs InformationPress the Time SET button Setting the ClockSetting the Timer Timer OperationTimer Playback Timer Recording Sleep TimerTimer off SLEEP-90 80, 70Troubleshooting Restoring factory settingsMaintenance SpecificationsTeac Corporation

AG-H380 specifications

The Teac AG-H380 is a high-fidelity audio receiver that exemplifies the perfect merging of classic design and modern technology. Tailored for audiophiles and casual listeners alike, this receiver boasts a wide range of features that ensure a superb listening experience.

At the heart of the AG-H380 is a robust amplifier section, delivering 80 watts per channel at 4 ohms. This power output guarantees that music playback is not only loud but also rich in detail and nuance. The receiver's high-current design allows it to drive even challenging speaker loads, making it versatile for various setups.

One of the standout features of the AG-H380 is its support for high-resolution audio formats. With native playback of PCM up to 32-bit/192 kHz and DSD up to DSD128, it caters to the modern listener who seeks superior sound quality. The inclusion of a built-in USB DAC enhances convenience, allowing users to connect their computers directly to the receiver without the need for additional components.

The AG-H380 does not shy away from versatility in connectivity. It offers multiple digital inputs, including optical and coaxial, along with traditional analog inputs for older equipment. Furthermore, Bluetooth connectivity allows for seamless streaming from smartphones and tablets, ensuring that users can enjoy their favorite tracks without cumbersome wires.

Another impressive aspect of the Teac AG-H380 is its advanced digital signal processing (DSP) capabilities. Advanced EQ settings enable users to customize their sound signature according to personal preferences and acoustic environments. This feature is especially beneficial for those who want to tailor their listening experience to specific rooms or speaker placements.

In terms of build quality, the AG-H380 reflects Teac's commitment to craftsmanship. The elegant design, characterized by a classic front panel with analog-style knobs, appeals to both retro enthusiasts and contemporary users. The all-metal chassis not only adds aesthetic appeal but also minimizes interference, leading to clearer sound.

Additionally, the AG-H380 includes a headphone output with a high-quality amplifier circuit, ensuring an exceptional listening experience for private sessions.

In conclusion, the Teac AG-H380 combines traditional aesthetics with cutting-edge technology, making it an ideal choice for both modern and classic audio enthusiasts seeking high-quality performance in an attractive package.
Top Page Image Contents