Teac Comprehensive Guide to Stereo Receiver Setup and Connections
Page 7

ASpeaker Connections

Caution:

To avoid damaging the speakers with a sudden high-level signal, be sure to switch the power off before connecting the speakers.

<Check the impedance of your speakers. Connect speaker with an impedance of 8 ohms or more.

<The black speaker terminals are - (negative).

Generally, the + side of the speaker cable is marked to make it distinguishable from the - side of the cable. Connect this marked side to the + terminal and the unmarked side to the black - terminal.

<Prepare the speaker cables for connection by stripping off approximately 10 mm or less of the outer insulation. (Removing too much insulation may lead to a short circuit if the bared wired should come in contact with each other.) Twist the strands of the stripped wires tightly together :

Caution:

The metal portions of the two separate wires should not touch or an electrical short can occur. Shorted wires can create a fire hazard or induce a failure in your equipment.

How to connect

1.Turn the terminal cap counterclockwise to loosen it. The speaker terminal caps cannot be fully removed from the base.

2.Insert the wire into the terminal fully and turn the terminal cap clockwise to securely connect it .

Make sure none of the wire insulation is under the terminal, only the bare, stripped wire.

3. Make sure it is fastened firmly by pulling the cable lightly.

BCD, TAPE MONITOR, VIDEO/AUX jacks

Analog 2-channel audio signal is input or output from these jacks. Connect the component with commercially-available RCA cables.

Make sure to connect:

white plug q white jack (L: left channel)

red plug q red jack (R: right channel)

CPHONO jacks/SIGNAL GND terminal

Connect the turntable’s RCA pin cords to PHONO jacks. Make sure to connect:

white plug q white jack (L: left channel)

red plug q red jack (R: right channel)

Connect the turntable’s ground cord to SIGNAL GND terminal.

DRESET switch

In the following cases, function buttons may not work properly.

•When the system is damaged by electrical shock.

•When the power is irregular or has electrical noises.

In these cases, press the RESET switch once or twice with a pencil or a ball-point pen lightly.

All the settings kept in memory (such as preset stations) will be erased.

EAC Outlet (Unswitched)

This outlet is active only when the unit is on or standby. When the power switch of the main unit is off, the outlet is inactive.

Caution:

Make sure that the total power consumption of all equipment connected to the outlet(s) does not exceed 100 watts or 1A.

FPower cord (AC)

Be sure to connect the power cord to an AC outlet which supplies the correct voltage.

Hold the power plug when plugging or unplugging the power cord. Never pull or yank on the power cord.

ENGLISH

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents 9A10271900 AG-790Left and Right Panels For U.S.ABefore Use ContentsFM Indoor Antenna Remote Control UnitConnecting Antennas Battery InstallationA./Canada/General Export Model How to connectAM Indoor Loop Antenna AM Outdoor AntennaGeneral export models only ConnectionVoltage Conversion Speakers a Speakers BPower cord AC Phono jacks/SIGNAL GND terminalReset switch AC Outlet UnswitchedS R Q P ONM L K J I H Names of Each ControlMuting indicator Power switchStandby indicator Speakers indicatorRecording Basic OperationTo listen to a source other than Tape Bass Control Listening through headphonesSelecting the speakers Loudness buttonSleep 90 80, 70...or Sleep TimerWhile muting is engaged, the Muting indicator blinks MutingStereo FM Mode ButtonRadio Reception Select the station you want to listen to auto selectionHow to select preset stations Preset TuningManual Memory Presetting Memory BackupMaintenance TroubleShootingSpecifications Avant Utilisation SommaireLire les consignes suivantes avant toute utilisation Antenne FM intérieure Boîtier de télécommandeRaccordements d’antenne Mise en place des pilesAntenne extérieure AM Antenne AM intérieure à cadreBranchement des enceintes Modèle Etats-Unis/Canada Modèle d’exportation généraleLa position du convertisseur de tension ConnexionsConversion de tension Modèle d’exportation générale seulementPrises CD, Tape MONITOR, VIDEO/AUX Prises Phono Borne Signal GND Masse DU SignalRéinitialisation Reset Branchement des haut-parleursS R Q P O NM L K J I H Noms des commandesTouche Tuning Mode Interrupteur PowerTouche s TUNING/PRESET Touche FM ModePour écouter une source autre que Tape Appuyez sur l’interrupteur POWER. L’appareil s’allumeFonctionnement de base EnregistrementEcoute avec un casque Commande des gravesCommande des aigus Allumer/Eteindre les enceintesAffichage normal Minuterie de mise hors serviceSilencieux Sleep 90 80, 70 ... ouSyntoniseur Touche FM ModeStéréo Comment sélectionner des stations préréglées Syntonisation prérégléePréréglage de mémoire manuel Mémoire de secoursEntretien DépannageCaractéristiques techniques Page Model number Serial number Teac Corporation
Related manuals
Manual 98 pages 60.17 Kb

AG-790 specifications

The Teac AG-790 is a versatile and high-performance audio receiver that combines state-of-the-art technology with classic design. Known for its dedication to delivering exceptional sound quality, the AG-790 is ideal for both audiophiles and casual listeners alike.

One of the standout features of the AG-790 is its amplification power. It boasts a robust output of 100 watts per channel, allowing it to drive large speakers and fill a room with rich, immersive audio. This power is paired with a high-quality digital-to-analog converter (DAC), which enhances the clarity and fidelity of the music being played. This ensures that every note and nuance of your favorite tracks is reproduced with remarkable precision.

In terms of connectivity, the Teac AG-790 offers a wide array of options. It includes multiple analog inputs, allowing you to connect various devices like turntables and CD players. Additionally, it features digital inputs, such as optical and coaxial connections, for use with modern digital sources. The inclusion of Bluetooth functionality allows for seamless streaming from smartphones and tablets, providing convenience and flexibility in how you enjoy your music.

Another key characteristic of the AG-790 is its built-in phono stage. This feature is particularly appealing to vinyl enthusiasts, as it allows you to connect a turntable directly without the need for an external preamp. The phono stage ensures that your vinyl records are played back with all the warmth and depth that analog recordings are known for.

The AG-790 also pays attention to user experience, featuring an intuitive front panel with a clear display and easily accessible controls. The remote control enhances this usability, allowing for easy adjustments from a distance. Furthermore, the receiver supports various audio formats, ensuring that it can accommodate a vast array of music types and sources.

In summary, the Teac AG-790 is a sophisticated audio receiver that combines powerful amplification, versatile connectivity, and user-friendly features. Its high-quality sound reproduction and thoughtful design make it a worthy addition to any audio setup, whether for home listening or entertaining guests. With the AG-790, Teac continues its tradition of delivering high-fidelity audio experiences that cater to modern music consumption habits.
Top Page Image Contents