Philips SC-BT735 Network Easy Setting, When you experience problems with settings

Network Easy Setting

Select “Wired” or “Wireless” and press [OK].

Network Easy Setting (Connection Test)

Select a connection mode.

Current setting : Wired

LAN cable connection:

Connect a LAN cable to the unit and select “Wired”.

Wireless LAN connection:

Connect the Wireless LAN Adaptor (DY-WL10) to the USB port and select “Wireless”.

Wired

Wireless

OK

RETURN

∫“Wired” connection

Follow the on-screen instructions to make your connection settings.

≥When you experience problems (> right)

∫“Wireless” connection

If you select “Wireless” and “Wireless LAN Adaptor is not connected.” is displayed, check that the Wireless LAN Adaptor is fully inserted. Alternatively, disconnect and reconnect it. If there is still no change in the display, consult your dealer for advice.

Select “WPS (PUSH button)” or “Search for access point” and then follow the on-screen instructions and make the settings.

Access Point Connection Setting

Select a connection method for access to Wireless LAN.

Please refer to the operating instructions of the access point about connection methods.

WPS (PUSH button)

Search for access point

WPS (PUSH button):
If your Wireless router (Access point)	e.g.,
supports WPS (PUSH button), you can
easily perform the settings by pressing
WPS button on it.
WPS (Wi-Fi Protected Setup) is a	1
standard that facilitates settings relating
to the connection and security of
wireless LAN devices.

1Press WPS button or corresponding button of Wireless router (Access point) until the lamp starts flashing.

≥For details, refer to the operating instruction of Wireless router (Access point).

2Press [OK].

*1 Wi-Fi Protected Setup-compatible Wireless router (Access point) may have the mark.

Search for access point:

Available Wireless routers (Access points) are searched and listed. You can select the one to use from the list.

1Press [3, 4] to select SSID*2 of Wireless router (Access point) you want to connect with. Then press [OPTION] to show information of the selected router, make a note of the authentication and encryption type.

Access Point Connection Setting

Select an access point to connect with. To search for access point again, please select "Search again" below.

SSID	Reception
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX	:XXXXXXXXXXXXXXX
SSID
XXXXXXXXXX	:802.11n/g/b (2.4GHz)
Wireless type
XXXXXXXXXX

	XXXXXXXXXXAuthentication type	:WPA-PSK
VQT2Q52	XXXXXXXXXXEncryption type	:AES
	XXXXXXXXXX

2Press [RETURN] and then press [OK].

Then select an item on the following screen which corresponds to the authentication type noted down in step 1 (> left).

Access Point Connection Setting

Select authentication type.

WPA2-PSK (AES/TKIP)

WPA-PSK (AES/TKIP)

Open/Shared Key (WEP)

Open system

Follow the on-screen instructions to make the settings.

≥Input your encryption key code in “Encryption Key” supplied with your Wireless router (Access point).

When you experience problems with settings

Access Point Connection Setting

Access Point Connection Setting

Failed to connect to the access point.

A conflict with other devices occurred.

Do you wish to setup Access Point

Connection Setting again ?

Yes	No
OK
Display	Check the following
A conflict with another	≥ Please wait a few moments,
device occurred.	and then try again.
A time out error occurred.	≥ Setting of the Wireless
	router (Access point) for
	MAC Address etc.
	≥ The signal may be weak.
	Using the USB extension
	cable supplied with the
An authentication error or a
	Wireless LAN Adaptor,
time out error occurred.
	adjust the position of the
	Wireless LAN Adaptor.
	≥ The SSID*2 and the
	encryption key of the
	Wireless router (Access
	point).
	≥ Please wait a few moments,
	and then try again.
A device error occurred.	≥ Connection of Wireless LAN
	Adaptor
	If there is no improvement in
	symptom, consult your
	dealer.

20

Search again

≥If you can not find the SSID*2, select “Search again”.