Schneider Electric 174 CEV CE Installation Requirements, Grounding, Ferrite Bead on RF-45 Cable

Page 24

Installing the Bridge Hardware

2.6CE Installation Requirements

If the bridge is being installed at a site that must meet CE requirements, the following steps must be taken to complete the installation.

Grounding

The bridge must be provided with a direct ground connection of 0.1 ohm or less. Mounting the bridge on a suitably grounded panel as described in Section 2.4 satisfies this requirement.

In addition the Modbus Plus cable must be grounded to the panel using the ground wire that is integral to the cable.

Ferrite Bead on RF-45 Cable

If the Ethernet network is being connected to the 10Base--T (RJ--45) connector, an approved ferrite bead must be installed on the cable at the connector.

The approved bead shown in Figure 9 and in Table 10 is enclosed in a plastic box which can be clipped over the network cable. It is not necessary to insert the cable through the bead before you install the RJ--45 connector on the cable.

Figure 9 Ferrite Bead on RJ-45 Cable (CE Requirement)

Cable Tie prevents bead from slipping

22 mm

Ferrite Bead

12 mm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

28A2029-0A0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

32 mm

Table 10 Approved Ferrite Bead

Manufacturer

Location and

 

(or Equivalent)

Telephone

Part Number

Steward

Livingston, Scotland, UK

28A2029--0A0

 

0044--1--506--414--200

 

20

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Breite 185 mm Höhe 230 mm Breite 178 mm Höhe 216 mm Training Contents Using the Bridge Software Uploading and Downloading FilesDiagnostic Tools GlossaryModbus Plus to Ethernet Bridge CEV 200 Introducing the Ethernet to Modbus Plus Bridge Illustrates a typical bridge connectionTCP/IP Bridge Message Transactions and Paths Read Discrete Output Status Specifications Power Input Tolerance CurrentAgency Status Installing the Bridge Hardware Overview Hardware Installation Setting the Modbus Plus Node Address SectionSetting the Ethernet Connector Jumper Section Connecting the Network and Power Cables SectionCE Installation Requirements Section Verifying the Network Communication SectionSetting the Modbus Plus Node Address Bridge Enclosure Screws Remove ScrewsDefault Setting Setting the Ethernet Connector Jumper JP2 AUI Mounting the Bridge Hardware Mounting RequirementsInstalling the Bridge Hardware Connecting the Network and Power Cables BNC CE Installation Requirements GroundingFerrite Bead on RF-45 Cable Ethernet Card Indicators Modbus Plus Card IndicatorsVerifying the Network Communication Factory Default Settings Ethernet Card DefaultsModbus Plus Card Defaults EdgePeriodic Maintenance Cleaning the FiltersUpper Filter Lower FilterConfiguring the Bridge Files Supplied With the Bridge Files Resident in the BridgeHost Software Disk Files Generated or Modified by the Bridge Software Startup SequenceOverview Software Configuration Setting the Ethernet ConfigurationSetting the Modbus Plus and TCP/IP Address Mapping Configuration With a Bootp Server SectionConfiguration With a Bootp Server Configuration With the Cfgutil Utility Starting CfgutilNavigating the Cfgutil Menu Required Configuration Fields Additional Configuration FieldsSaving the Configuration Address Mapping Table FieldsHow Mapping Works TCP/IP to Modbus Plus Destination Indexes 1 .. Mapped RoutingDestination Index 255 Bridge Internal Command Destination Indexes 0 and 254 Dynamic Message RoutingReserved Destination Indexes Setting the Mapping TCP/IP to Modbus Plus 1 MB+ Mapping Table Layout and Default EntriesEntry Example MB+ Mapping Table Saving the MappingHow Mapping Works Modbus Plus to TCP/IP Bytes 1 and 2. Bridge Node Address and PathByte 3. First Bridge’s IP Routing Byte 4. Second Bridge’s Modbus Plus RoutingMessage is Originated Bridge 1 Maps the Message to TCP/IPBridge 2 Maps the Message to Modbus Plus Message is DeliveredSetting the Mapping Modbus Plus to TCP/IP TCP Mapping Table Layout and Default EntriesEntry Example TCP Mapping Table Example Modbus Plus to TCP/IP MappingSetting Up the Bridge for Dynamic Routing Contents Hex Contents DecimalDynamic Routing of Messages ExampleUsing Dynamic Routing Clearing the Bridge’s Configuration SetupClearing the Configuration Using the Bridge Software Bridge Software Contents SW-MBPE-000 Using the Software in Custom Configurations Minimum Requirements for Custom Bridge ConfigurationsSetting Up a Custom Bridge Configuration DEVICE=MBPHOST.SYS /md000 /s5d /n0 /r2 Uploading and Downloading Files Configuring an Http Server Configuration ExampleCgi-bin Uploading Files to a Host Upload OverviewInitiating an Upload Upload Example RTE.CFGDownloading Files to the Bridge Download OverviewInitiating a Download Download Example Diagnostic Tools Diagnostics Overview Ethernet DiagnosticsLogging the Bridge’s Activity Modbus Plus Diagnostics MbpstatLogging the Bridge’s Activity How Logging WorksStarting Logging Stopping LoggingMode a Channel Logging Menu Saving the Logging Status and Log FileTcpinfo StartingPing Starting Ping at the BridgeStarting Ping at the Host Starting Mbpstat Selecting the Network to be AnalyzedNetwork Selection Examples Typical Mbpstat Routing Your Mbpstat Menu Entering Node AddressesOption 1 Set Routing Parameters Set Routing ParametersOption 2 Monitor Network Activity Monitor Network ActivityOption 3 Read Global Data Read Global DataOption 4 Global Data Present Table Global Data Present TableOption 5 Node Active Station Table Node Active Station TableOption 6 Node Error Statistics 05.00.00.00.00 Failure 244Option 7 Token Station Table Token Station TableOption 8 Token Owner Work Table Token Owner Work TableOption 9 Current Internal Path Transactions PathOption 10 Node Personality Node PersonalityMessage Examples Mstr Example TCP/IP Node Mstr in TCP/IP NodeMstr Example Modbus Plus Node Mstr in Modbus Plus NodeNCB Return Codes Network Control Block NCB Return Codes ERRsuccessGlossary Default gateway FieldFrame Framing typesInternet IP AddressLayer MAC AddressSwitch RepeaterRouter ServerUTP Winsock

174 CEV specifications

Schneider Electric, a global leader in energy management and automation, has designed the Schneider Electric 174 CEV to meet the evolving demands of industrial applications. This innovative controller is engineered to enhance efficiency, flexibility, and reliability across various sectors.

One of the main features of the Schneider Electric 174 CEV is its robust communication capabilities. It supports multiple protocols, including Ethernet/IP, Modbus, and both serial and parallel communication interfaces. This multiplicity allows seamless integration with existing systems, ensuring that users can connect and manage devices within their operational setup without extensive changes to their infrastructure.

The 174 CEV is equipped with a powerful processing unit that ensures rapid data processing and real-time analytics. This is particularly advantageous for industries where quick decision-making is crucial. The controller is designed to handle large data sets and perform complex functions, all while maintaining optimal performance levels.

Another significant aspect of the Schneider Electric 174 CEV is its modular design. This feature allows for tailored solutions suited to specific application needs. Users can customize their setup by adding or removing modules based on their operational requirements, which enhances the controller’s versatility and longevity.

In terms of technology, the 174 CEV utilizes advanced algorithms for energy management and optimization. Users can benefit from predictive maintenance capabilities, which leverage data analytics to anticipate equipment failures before they occur. This proactive approach reduces downtime and maintenance costs, ultimately contributing to higher operational efficiency.

The controller also emphasizes user-friendly interfaces. With intuitive programming tools and a graphical user interface, operators can easily navigate through its functionalities, customize settings, and monitor performance metrics. This accessibility fosters greater user engagement and reduces the learning curve for new operators.

Safety is a top priority in the design of the Schneider Electric 174 CEV. The controller is built with compliance to international safety standards, ensuring that it can be deployed in a wide range of industries while guaranteeing the protection of both personnel and equipment.

Overall, the Schneider Electric 174 CEV stands out due to its combination of robust communication options, powerful processing capabilities, modular design, and user-friendly features. With its focus on energy efficiency and safety, the 174 CEV is an excellent choice for fulfilling the increasing demands of modern industrial environments.
Top Page Image Contents