Schneider Electric 174 CEV manual Setting the Mapping Modbus Plus to TCP/IP

Page 42

Configuring the Bridge

3.8Setting the Mapping: Modbus Plus to TCP/IP

Each message from a Modbus Plus node contains a five--byte routing path field (See Section 3.7). The bridge uses the third byte to index into its TCP Mapping table, extracting an IP address from that entry.

You can edit the table to map the Modbus Plus routing path’s third byte to specific IP addresses in your application.

3.8.1TCP Mapping Table Layout and Default Entries

The TCP Mapping table contains 255 fields, labeled TCP_1 through TCP_255. These fields define IP addresses for messages (from Modbus Plus nodes) which contain 1 through 255 decimal in byte 3 of the Modbus Plus message routing path.

By default the bridge automatically sets the first three bytes of each IP address to match the first three bytes of the bridge’s IP address. (See Figure 14 and Section

3.4.3for an example of configuring the bridge’s IP address.) The bridge sets the fourth byte of the IP address mapping to the range 1 ... 255.

For example, if you configure the bridge’s IP address as:

205.167.7.65

the TCP Mapping table’s 255 locations will automatically default to:

TCP_1:

205.167.7.1

TCP_2:

205.167.7.2

. . .

. . .

TCP_255:

205.167.7.255

Figure 18 shows an example of typical default TCP mapping, with one custom routing entry made by the user.

38

Image 42
Contents Breite 185 mm Höhe 230 mm Breite 178 mm Höhe 216 mm Training Contents Using the Bridge Software Uploading and Downloading FilesDiagnostic Tools GlossaryModbus Plus to Ethernet Bridge CEV 200 Introducing the Ethernet to Modbus Plus Bridge Illustrates a typical bridge connectionTCP/IP Bridge Message Transactions and Paths Read Discrete Output Status Specifications Power Input Tolerance CurrentAgency Status Installing the Bridge Hardware Setting the Ethernet Connector Jumper Section Overview Hardware InstallationSetting the Modbus Plus Node Address Section Connecting the Network and Power Cables SectionCE Installation Requirements Section Verifying the Network Communication SectionSetting the Modbus Plus Node Address Bridge Enclosure Screws Remove ScrewsDefault Setting Setting the Ethernet Connector Jumper JP2 AUI Mounting the Bridge Hardware Mounting RequirementsInstalling the Bridge Hardware Connecting the Network and Power Cables BNC CE Installation Requirements GroundingFerrite Bead on RF-45 Cable Ethernet Card Indicators Modbus Plus Card IndicatorsVerifying the Network Communication Factory Default Settings Ethernet Card DefaultsModbus Plus Card Defaults EdgeUpper Filter Periodic MaintenanceCleaning the Filters Lower FilterConfiguring the Bridge Files Supplied With the Bridge Files Resident in the BridgeHost Software Disk Files Generated or Modified by the Bridge Software Startup SequenceSetting the Modbus Plus and TCP/IP Address Mapping Overview Software ConfigurationSetting the Ethernet Configuration Configuration With a Bootp Server SectionConfiguration With a Bootp Server Configuration With the Cfgutil Utility Starting CfgutilNavigating the Cfgutil Menu Saving the Configuration Required Configuration FieldsAdditional Configuration Fields Address Mapping Table FieldsHow Mapping Works TCP/IP to Modbus Plus Destination Indexes 1 .. Mapped RoutingDestination Index 255 Bridge Internal Command Destination Indexes 0 and 254 Dynamic Message RoutingReserved Destination Indexes Setting the Mapping TCP/IP to Modbus Plus 1 MB+ Mapping Table Layout and Default EntriesEntry Example MB+ Mapping Table Saving the MappingByte 3. First Bridge’s IP Routing How Mapping Works Modbus Plus to TCP/IPBytes 1 and 2. Bridge Node Address and Path Byte 4. Second Bridge’s Modbus Plus RoutingBridge 2 Maps the Message to Modbus Plus Message is OriginatedBridge 1 Maps the Message to TCP/IP Message is DeliveredSetting the Mapping Modbus Plus to TCP/IP TCP Mapping Table Layout and Default EntriesEntry Example TCP Mapping Table Example Modbus Plus to TCP/IP MappingDynamic Routing of Messages Setting Up the Bridge for Dynamic RoutingContents Hex Contents Decimal ExampleUsing Dynamic Routing Clearing the Bridge’s Configuration SetupClearing the Configuration Using the Bridge Software Bridge Software Contents SW-MBPE-000 Using the Software in Custom Configurations Minimum Requirements for Custom Bridge ConfigurationsSetting Up a Custom Bridge Configuration DEVICE=MBPHOST.SYS /md000 /s5d /n0 /r2 Uploading and Downloading Files Configuring an Http Server Configuration ExampleCgi-bin Uploading Files to a Host Upload OverviewInitiating an Upload Upload Example RTE.CFGDownloading Files to the Bridge Download OverviewInitiating a Download Download Example Diagnostic Tools Diagnostics Overview Ethernet DiagnosticsLogging the Bridge’s Activity Modbus Plus Diagnostics MbpstatStarting Logging Logging the Bridge’s ActivityHow Logging Works Stopping LoggingMode a Channel Logging Menu Saving the Logging Status and Log FileTcpinfo StartingPing Starting Ping at the BridgeStarting Ping at the Host Starting Mbpstat Selecting the Network to be AnalyzedNetwork Selection Examples Typical Mbpstat Routing Your Mbpstat Menu Entering Node AddressesOption 1 Set Routing Parameters Set Routing ParametersOption 2 Monitor Network Activity Monitor Network ActivityOption 3 Read Global Data Read Global DataOption 4 Global Data Present Table Global Data Present TableOption 5 Node Active Station Table Node Active Station TableOption 6 Node Error Statistics 05.00.00.00.00 Failure 244Option 7 Token Station Table Token Station TableOption 8 Token Owner Work Table Token Owner Work TableOption 9 Current Internal Path Transactions PathOption 10 Node Personality Node PersonalityMessage Examples Mstr Example TCP/IP Node Mstr in TCP/IP NodeMstr Example Modbus Plus Node Mstr in Modbus Plus NodeNCB Return Codes Network Control Block NCB Return Codes ERRsuccessGlossary Frame Default gatewayField Framing typesLayer InternetIP Address MAC AddressRouter SwitchRepeater ServerUTP Winsock

174 CEV specifications

Schneider Electric, a global leader in energy management and automation, has designed the Schneider Electric 174 CEV to meet the evolving demands of industrial applications. This innovative controller is engineered to enhance efficiency, flexibility, and reliability across various sectors.

One of the main features of the Schneider Electric 174 CEV is its robust communication capabilities. It supports multiple protocols, including Ethernet/IP, Modbus, and both serial and parallel communication interfaces. This multiplicity allows seamless integration with existing systems, ensuring that users can connect and manage devices within their operational setup without extensive changes to their infrastructure.

The 174 CEV is equipped with a powerful processing unit that ensures rapid data processing and real-time analytics. This is particularly advantageous for industries where quick decision-making is crucial. The controller is designed to handle large data sets and perform complex functions, all while maintaining optimal performance levels.

Another significant aspect of the Schneider Electric 174 CEV is its modular design. This feature allows for tailored solutions suited to specific application needs. Users can customize their setup by adding or removing modules based on their operational requirements, which enhances the controller’s versatility and longevity.

In terms of technology, the 174 CEV utilizes advanced algorithms for energy management and optimization. Users can benefit from predictive maintenance capabilities, which leverage data analytics to anticipate equipment failures before they occur. This proactive approach reduces downtime and maintenance costs, ultimately contributing to higher operational efficiency.

The controller also emphasizes user-friendly interfaces. With intuitive programming tools and a graphical user interface, operators can easily navigate through its functionalities, customize settings, and monitor performance metrics. This accessibility fosters greater user engagement and reduces the learning curve for new operators.

Safety is a top priority in the design of the Schneider Electric 174 CEV. The controller is built with compliance to international safety standards, ensuring that it can be deployed in a wide range of industries while guaranteeing the protection of both personnel and equipment.

Overall, the Schneider Electric 174 CEV stands out due to its combination of robust communication options, powerful processing capabilities, modular design, and user-friendly features. With its focus on energy efficiency and safety, the 174 CEV is an excellent choice for fulfilling the increasing demands of modern industrial environments.