Patton electronic 2884 manual Industry Canada Notice, CE Declaration of Conformity

Page 38

IpLink 2884/2888 Getting Started Guide

A • Compliance information

 

 

The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.

If trouble is experienced with this equipment, for repair or warranty information, please contact our company. If the equipment is causing harm to the telephone network, the telephone company may request that you dis- connect the equipment until the problem is resolved.

Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information.

Industry Canada Notice

This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed by the registration number. The abbreviation, IC, before the registration number signifies that regis- tration was performed based on a Declaration of Conformity indicating that Industry Canada technical speci- fications were met. It does not imply that Industry Canada approved the equipment.

This Declaration of Conformity means that the equipment meets certain telecommunications network protec- tive, operational and safety requirements. The Department does not guarantee the equipment will operate to the user's satisfaction. Before installing this equipment, users should ensure that it is permissible to be con- nected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. In some cases, the company’s inside wiring associated with a single line individual service may be extended by means of a certified connector assembly (telephone extension cord). The customer should be aware that compliance with the above condition may not prevent degradation of service in some situations. Repairs to some certified equipment should be made by an authorized maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment mal- functions, may give the telecommunications company cause to request the user to disconnect the equipment. Users should ensure for their own protection that the ground connections of the power utility, telephone lines and internal metallic water pipe system, are connected together. This protection may be particularly important in rural areas.

CE Declaration of Conformity

This equipment conforms to the requirements of Council Directive 1999/5/EC on the approximation of the laws of the member states relating to Radio and Telecommunication Terminal Equipment and the mutual rec- ognition of their conformity.

The safety advice in the documentation accompanying this product shall be obeyed. The conformity to the above directive is indicated by CE sign on the device.

The signed Declaration of Conformity can be downloaded at www.patton.com/certifications.

Authorized European Representative

D R M Green

European Compliance Services Limited.

Oakdene House, Oak Road

Watchfield, Swindon, Wilts SN6 8TD, UK

Industry Canada Notice

38

Page 37 Page 39
Image 38
Page 37 Page 39
Contents IpLink Mailsupport@patton.com Summary Table of Contents Table of Contents Initial configuration Cabling List of Figures List of Tables Structure About this guideAudience Precautions Safety when working with electricityGeneral conventions Typographical conventions used in this documentGeneral observations Node Chapter contents General informationIpLink Model 2884 Overview IpLink ModelIpLink Model 2888 Overview Model 2888 Features Features and BenefitsModel 2884 Features Rear and Front Panels IpLink 2884/2888 rear panelLAN ETH IpLink 2884/2888 front panel LEDApplications overview Typical IPLink 2884 Application Typical application for IPLink ModelTypical IPLink 2888 Application IpLink installation Site log Planning the installationNetwork Diagram Network informationInstalling the IpLink 2884/2888 Installing cables Connect the cables in the following orderConnecting the power supply Connecting DC Power to the 288x DC Power Supply Initial configuration Introduction Connecting the IpLink to your PCConnecting and logging in via the Ethernet port Configuring the desired IP address Connecting and logging in via the Console portFactory-default IP settings Changing the IP address Connecting the IpLink to the networkLogin Contacting Patton for assistance Patton support headquarters in the USA Warranty coverageContact information Out-of-warranty service RMA numbersAppendix a Compliance information Radio and TV Interference SafetyCompliance FCC Part 68 Acta StatementAuthorized European Representative Industry Canada NoticeCE Declaration of Conformity Appendix B Specifications Management WAN PortsEthernet Ports ProtocolsPhysical Power SupplySecurity Appendix C Cabling Connecting a serial terminal ConsoleEthernet Connecting an E1 port to an NT1 E1 PortConnecting a T1 port to an NT device T1 PortAppendix D Port pin-outs Console port EIA-561 RJ-45 8-pin portT1/E1 port Appendix E End user license agreement End User License Agreement Termination Other licenses
Related manuals
Manual 51 pages 18.45 Kb

2884 specifications

The Patton Electronic 2884 is a powerful and versatile networking solution designed to facilitate efficient data communication and enhance connectivity in various environments. Known for its reliability and performance, the 2884 is especially favored in enterprise applications, remote locations, and industrial settings.

One of the standout features of the Patton 2884 is its ability to support a wide array of communication protocols. This flexibility allows it to seamlessly integrate into various network architectures, making it an ideal choice for businesses looking to streamline their connectivity infrastructure. Equipped with advanced Ethernet and serial connectivity options, the device can handle multiple data types and formats, ensuring consistency and efficiency in data transmission.

The 2884 is built with robust technologies that enhance its overall performance. With support for both T1 and E1 circuits, the device is capable of delivering high-speed data transfers while reducing latency, which is crucial for applications that require real-time data access. Additionally, the unit employs sophisticated error correction and data compression techniques to optimize the throughput while maintaining data integrity.

In terms of security, the Patton 2884 offers advanced features that protect sensitive data during transmission. The encryption capabilities ensure that information remains confidential as it traverses potentially unsecured networks, which is critical in today’s environment of increasing cyber threats. The device also supports multiple authentication methods to verify authorized users, further safeguarding the network.

The design of the Patton 2884 emphasizes ease of use and management. It comes equipped with a user-friendly interface, enabling administrators to configure and monitor the device with minimal effort. The advanced diagnostic features allow for quick troubleshooting, reducing downtime and ensuring that networks operate smoothly.

Another important characteristic of the Patton 2884 is its rugged construction, which makes it suitable for deployment in harsh environments. Its durability ensures that the device can withstand extreme temperatures and physical shocks, a key consideration for installations in industrial sites or outdoor settings.

In conclusion, the Patton Electronic 2884 stands out as a reliable, flexible, and secure choice for organizations seeking to enhance their networking capabilities. With its advanced features and robust design, it is equipped to meet the demands of modern data communication, making it a valuable asset for any organization.
Top Page Image Contents