Patton electronic RS-232 user manual Configuration Switches, Opening the Case, Switch Settings

Page 3

3.0 CONFIGURATION

The Model 1035 provides sixteen configuration switches, which allow selection of data rates, clocking methods, V.54 test modes, RTS/CTS delay and DTE control of test functions. This section describes switch locations and explains all possible switch configurations.

3.1 CONFIGURATION SWITCHES

The Model 1035’s unique set of sixteen internal DIP switches allows configuration to an extremely wide range of applications. These switches are grouped into two eight-switch sets and are located on the inside of the unit (Figure 1). For instructions on opening the Model 1035 case, see Section 3.2.

 

 

 

 

 

 

 

8

 

 

 

 

 

7

 

 

 

 

 

 

 

 

 

 

6

 

 

 

 

 

1 2 3 4 5

 

OFF

 

SW2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8

 

 

 

SW1

 

3 4 5 6 7

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1 2

 

OFF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 1. The inside of the Model 1035

Figure 2 shows the orientation of the switches, including the ON/OFF positions.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ON

1

2

3

4

5

6

7

8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DHS-8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OFF

 

 

 

 

 

 

 

 

 

 

 

 

OFF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 2. Close up of configuration switches

3.2 OPENING THE CASE

Open the unit by gently inserting a screwdriver into the special pry slot on the plastic case (below). You don't have to worry about breaking the plastic.

3.3 SWITCH SETTINGS

All possible settings for the Model 1035’s configuration switches are presented in the summary table and descriptions on the following pages. If you have additional questions regarding configuration, contact Patton Technical Support at (301) 975-1007.

3

4

Image 3
Contents User Manual Description ServiceFeatures Radio and TV InterferenceConfiguration Switches Switch SettingsOpening the Case SW2 Summary Table Switch SET SW1Switch SET SW2 SW1 Summary TableTwisted Pair Connection Using RJ-11 or RJ-45 SignalConnection to the Twisted Pair Interface Connection to AN RS-232 DCE Device Signal PIN# Color ‡Connection to the RS-232 and V Interfaces Connection to a DTE DeviceLocal Analog Loopback LAL Front Panel SwitchesLED Status Monitors Test ModesPatton Model 1035 Specifications POWER-DOWNDirection RS-232 PIN-OUT Reference DB-25 PIN Configurations Block Diagram