Patton electronic 2977 user manual DialFire PTE Isdn E1 Euro Isdn Configuration Worksheet

Page 21

Model 2977 DialFire RAS User Manual

2 • Preparation

 

 

DialFire PTE ISDN E1 (Euro ISDN) Configuration Worksheet

Use the worksheet below to collect the information that may be required to complete the configuration of your DialFire PTE adapter within your operating system environment.

Note Not all operating systems support all parameters.

Note The parameters on this page are for ISDN E1 (Euro ISDN).

Parameter

 

 

Value

 

 

 

 

Line Type

E1

 

 

Framing

[ ] CEPT with CRC4

[ ] CEPT without CRC4

 

 

 

Coding

[ ] HDB3 [ ] AMI

 

Signaling

[ ] ETSI (Euro ISDN)

[ ] None

 

 

Leased Time Slots

List which, if any, E1 time slots are leased:

 

 

Modem Nationality

Enter the country in which the PTE adapter will be operated:

 

 

Before You Install the DialFire

Order the ISDN Line

RAS B4ST Adapter…

If you do not have an ISDN line installed, you need to contact your tele-

.

phone company and order a Basic Rate ISDN line (2B+D) with the follow-

 

 

ing recommended configuration:

 

 

Note If your telephone company supports either of the

 

 

following ISDN Ordering Codes, request that your

 

 

ISDN line be configured to one of them.

 

EZ-ISDN 1 (Preferred)

 

Capability S

 

 

If your telephone company does not support either of these Ordering

 

Codes, request the following ISDN line configuration:

 

Switch Type: National ISDN 1 (preferred), ETSI, AT&T 5ESS, or Nortel

 

 

DMS 100

 

 

ISDN Basic Rate Interface (BRI) service (2B+D)

 

2 B channels, D channel for signaling only (no D channel packet data)

 

Circuit Switched data and voice (CSD/CSV) on each channel

 

Dynamic TEI

 

 

Multipoint bus configuration

 

Terminal type A (AT&T Custom switch only)

 

No EKTS or special services or features

 

*You must select a long distance carrier and forward your choice, along with the Ordering

 

Code or line configuration, to your telephone company

 

 

 

 

After completing the worksheet, go to section chapter 3, “Installing the Model 2977 adapter” on page 26.

DialFire PTE ISDN E1 (Euro ISDN) Configuration Worksheet

21

Image 21
Contents Remote Access Server Patton Electronics Company, Inc Contents Contents Using the Viewer Radio and TV Interference Industry Canada NoticeFCC Information DialFire B4/ST RAS CE Notice FCC Part 68 Compliance StatementStructure AudiencePrecautions Typographical conventions used in this documentGeneral conventions Mouse conventions DialFire Model 2977 RAS Adapters Chapter contentsModel 2977 DialFire RAS overview IntroductionModel 2977 DialFire T1/E1 RAS Model 2977/B4 DialFire BRI RASMicrosoft Supported Operating SystemsPreparation Completing a configuration worksheet DialFire Basic BRI Configuration Worksheet Patton Electronics DialFire Channelized T1, Short-Haul Configuration Worksheet Order the Isdn Line DialFire PTE Isdn E1 Euro Isdn Configuration WorksheetNone Interface ID for Port 48 PT2 Only 127 Leased Time Slots Before You Install DialFire Isdn T1 PRI, Short-Haul Configuration Worksheet EZ-ISDN 1 Preferred Capability S Installing the Model 2977 adapter Determining your line termination requirements Model 2977 B4 ST adapter installationDialFire BRI connectors and line-terminating DIP switch Installing the DialFire RAS B4ST AdapterReplace the computer’s cover Model 2977 B4 U adapter installationDialFire BRI connectors PE1 & PE2 Connector Locations Model 2977 PE1 PE2 adapter installationPT1 & PT2 Connector Locations Model 2977 PT1 PT2 adapter installationModel 2977 daughter board installation Parts ListInstallation Mating Connectors Plated-through holes Spacers Screws Mating Connectors Driver installation Configuration Driver installation and configuration Procedure Driver installation for the Windows 2000 operating systemInstalling the Driver Supported ProductsUpgrading the Driver ProcedureDriver installation for the Windows XP operating system Configuring Outgoing Dial-up Networking Connections Configuring Incoming Dial-up Networking ConnectionsChanging Phone and Modem Options Changing Adapter PropertiesUsing the Windows Troubleshooter Uninstalling the DriverInstalling the MS Loopback Adapter Installing the downloaded driverConfiguring the Adapter First Time Changing the Adapter ConfigurationConfiguring RAS Ports Configuring RAS Dial-in Permissions Configuring Modems on COM Ports Configuring Dial-up Networking ConnectionsChanging Serial Port Names Using the Viewer Starting Patton View About Patton ViewOperation and shutdown De-activating the Model Activating the ModelContacting Patton for assistance Contact information Warranty coverageRMA numbers Return for credit policyAppendix a Software License Agreements Software License Agreements Software License Agreements Software License Agreements
Related manuals
Manual 56 pages 44.55 Kb