Patton electronic 2977 Configuring the Adapter First Time, Changing the Adapter Configuration

Page 45

Model 2977 DialFire RAS User Manual

4 • Driver installation and configuration

 

 

7.Enter either d:\i386\ (for Intel processors; use d:\alpha\ for Alpha systems) and load your Windows NT CD- ROM. (This assumes that your CD-ROM drive is drive D.)

The system asks you to specify a Frame Type.

8.Choose 802.3 and then Continue.

The network bindings page appears.

9.Choose Next to accept the bindings and Next again to start the network.

10.Enter the name of your computer and workgroup and click Next.

11.Restart your computer to activate Windows NT Networking.

Configuring the Adapter: First Time

Use this procedure to configure a Patton Electronics adapter for the first time.

Procedure

1.Install the driver. Refer to “Installing the downloaded driver” on page 44.

2.Use the configuration wizard and online Help to guide you through initial configuration.

Changing the Adapter Configuration

Use this procedure to change the configuration of a previously-configured Patton Electronics adapter.

Procedure

1.Access the configuration utility by choosing Control Panel > Network > Adapters.

2.Choose the adapter from the list and then Properties. The adapter properties page appears.

3.Select an item to reconfigure from the left-hand pane of the properties page and then choose Properties.

4.Change the configuration as required and then choose OK.

Configuring RAS Ports

Use this procedure to configure Patton Electronics devices as RAS ports (sometimes called RAS capable devices).

Procedure

1.If you need to access Windows NT RAS, choose Control Panel > Network > Services > Remote Access Services > Properties.

2.To add a modem port to the RAS configuration, do the following:

Choose Add > Install Modem.

Choose <Don't detect my modem; I will select it from a list> and then choose Next.

Choose Patton Electronics International from the Manufacture's list and Patton Electronics RAS 56K Modem from the

Model's list and then choose Next.

Install this modem type on the ports you want to use for RAS and then follow the prompts until you get to the Add RAS Device dialog.

From the Add RAS Device dialog, choose devices to add to RAS and then OK.

Driver installation for the Microsoft Windows NT operating system

45

Image 45
Contents Remote Access Server Patton Electronics Company, Inc Contents Contents Using the Viewer Radio and TV Interference Industry Canada NoticeFCC Information DialFire B4/ST RAS CE Notice FCC Part 68 Compliance StatementStructure AudiencePrecautions Typographical conventions used in this documentGeneral conventions Mouse conventions DialFire Model 2977 RAS Adapters Chapter contentsModel 2977 DialFire RAS overview IntroductionModel 2977 DialFire T1/E1 RAS Model 2977/B4 DialFire BRI RASMicrosoft Supported Operating SystemsPreparation Completing a configuration worksheet DialFire Basic BRI Configuration Worksheet Patton Electronics DialFire Channelized T1, Short-Haul Configuration Worksheet Order the Isdn Line DialFire PTE Isdn E1 Euro Isdn Configuration WorksheetNone Interface ID for Port 48 PT2 Only 127 Leased Time Slots Before You Install DialFire Isdn T1 PRI, Short-Haul Configuration Worksheet EZ-ISDN 1 Preferred Capability S Installing the Model 2977 adapter Determining your line termination requirements Model 2977 B4 ST adapter installationDialFire BRI connectors and line-terminating DIP switch Installing the DialFire RAS B4ST AdapterReplace the computer’s cover Model 2977 B4 U adapter installationDialFire BRI connectors PE1 & PE2 Connector Locations Model 2977 PE1 PE2 adapter installationPT1 & PT2 Connector Locations Model 2977 PT1 PT2 adapter installationModel 2977 daughter board installation Parts ListInstallation Mating Connectors Plated-through holes Spacers Screws Mating Connectors Driver installation Configuration Driver installation and configuration Procedure Driver installation for the Windows 2000 operating systemInstalling the Driver Supported ProductsUpgrading the Driver ProcedureDriver installation for the Windows XP operating system Configuring Outgoing Dial-up Networking Connections Configuring Incoming Dial-up Networking ConnectionsChanging Phone and Modem Options Changing Adapter PropertiesUsing the Windows Troubleshooter Uninstalling the DriverInstalling the MS Loopback Adapter Installing the downloaded driverConfiguring the Adapter First Time Changing the Adapter ConfigurationConfiguring RAS Ports Configuring RAS Dial-in Permissions Configuring Modems on COM Ports Configuring Dial-up Networking ConnectionsChanging Serial Port Names Using the Viewer Starting Patton View About Patton ViewOperation and shutdown De-activating the Model Activating the ModelContacting Patton for assistance Contact information Warranty coverageRMA numbers Return for credit policyAppendix a Software License Agreements Software License Agreements Software License Agreements Software License Agreements
Related manuals
Manual 56 pages 44.55 Kb