Patton electronic 2174 user manual Connecting the Line Interface

Page 11

3.1 CONNECTING THE LINE INTERFACE

The Interconnecting cables shall be acceptable for

external use and shall be rated for the proper applica-

tion with respect to voltage, current, anticipated tem-

CAUTION perature, flammability, and mechanical serviceability.

The Model 2174 supports communication between two peer Ethernet LAN sites over a distance of up to 10,000 ft (3 km) over 24 AWG (0.5 mm) twisted-pair wire, Cat5+, or 75-ohm BNC.

Note Actual distance and link performance may vary depending on the environment and type/gauge of wire used.

Follow the steps below to connect the Model 2174 CopperLINK Inter- faces.

Note The Model 2174 units work in pairs. One of the units must be configured as a (L) Local unit, and the other unit must be config- ured as a (R) Remote unit.

Connecting the Line Interface for Model 2174/EUI or 2174/TB

1.To function properly, the two Model 2174s must be connected together using twisted-pair, unconditioned, dry, metal wire, between 19 (0.9mm) and 26 AWG (0.4mm). Leased circuits that run through signal equalization equipment are not acceptable.

2.The Model 2174 is equipped with an RJ-45 interface jack (Figure 3) or terminal block (Figure 4) that can be used on the CopperLINK inter- face. The CopperLINK interface is a two-wire interface. Observe the signal/pin relationships on the Model 2174's CopperLINK interface jack.

The RJ-45 connector on the Model 2174's twisted pair interface is polar- ity insensitive and is wired for a two-wire interface. The signal/pin rela- tionship is shown in Figure 3.

 

1 (no connection)

1

2 (no connection)

23 (no connection)

44 (RING)

55 (TIP)

6

6 (no connection)

7

7 (no connection)

8

8 (no connection)

Figure 3. Model 2174 (RJ-45) twisted pair line interfac.

11

Image 11
Contents User Manual Contents Line Rate & Reach Chart, Based on 24 AWG 0.5 MM Radio and TV Interference FCC Part Warranty InformationRegulatory Information PstnTel +1 301 Email support@patton.com ServiceCE Declaration of Conformity Authorized European RepresentativeMust have an earth ground Safety When Working with ElectricityPage Description FeaturesGeneral Information Typical application InstallationModel 2174 rear panel options Connecting the Line Interface for Model 2174/EUI or 2174/TB Connecting the Line InterfaceConnecting the 10/100BASE-T Ethernet Interface Connecting the Line Interface for Model 2174/BNCConfiguring the Hardware DIP Switches Connecting PowerConfiguration Position Description Configuring DIP Switch S1S1-2 S1-3 Setting Switch S1-1 Local/Remote ConfigurationS1-1 Setting Switches S1-2 and S1-3 Symmetric/Asymmetric OperationLED OperationFront Panel LED Status Monitors Dimensions LED Status IndicatorsPower Supply Temperature RangePatton Model # Description Appendix BCopperlink Interface Appendix C10/100BASE-T Interface RJ-45Appendix D Mode Distance in Feet Mbps Long RangeMode Distance in Feet Mbps High Speed Page Page Copyright Patton Electronics Company All Rights Reserved

2174 specifications

The Patton Electronics 2174 is a versatile and robust device widely recognized for its capability to facilitate seamless connectivity in various communication environments. Designed specifically to serve the demands of both business and industrial applications, this equipment excels in providing reliable data transmission over long distances.

One of the main features of the Patton 2174 is its advanced DSL technology. It effectively supports ADSL and VDSL standards, enabling high-speed internet connections essential for modern networking needs. This feature is particularly beneficial for businesses that require fast and reliable internet access to maintain productivity and efficiency.

The device is equipped with a user-friendly web interface, allowing for effortless configuration and management. This intuitive interface empowers users to easily set up and monitor their connections without the need for specialized technical knowledge. In addition, the unit supports SNMP for network management, allowing IT professionals to monitor the device remotely, troubleshoot efficiently, and optimize performance.

The Patton 2174 boasts enhanced security features, including support for various encryption protocols. This ensures that data transmitted over the network is protected from unauthorized access, a crucial characteristic for organizations handling sensitive information.

Another notable attribute of the Patton 2174 is its robust build quality. Designed for durability, the device is capable of operating in a wide range of environmental conditions. This durability makes it suitable for both indoor and outdoor deployments, further extending its versatility.

The device also supports Power over Ethernet (PoE), allowing it to receive power through the network cable, simplifying installation by eliminating the need for additional power sources. This feature is especially advantageous in remote locations where access to power outlets is limited.

In terms of connectivity, the Patton 2174 includes multiple Ethernet ports, offering flexibility for integration into existing systems. Its capability to support both point-to-point and point-to-multipoint configurations makes it an excellent choice for various networking topologies.

Overall, the Patton Electronics 2174 stands out as a reliable, feature-rich solution for businesses and organizations seeking to enhance their communication infrastructure. With its combination of advanced technology, user-friendly management capabilities, and robust design, it represents a significant investment in the future of connectivity.