Patton electronic 2977 DialFire PTE Isdn E1 Euro Isdn Configuration Worksheet, Order the Isdn Line

Page 24

2 • Preparation

Model 2977 DialFire RAS User Guide

 

 

DialFire PTE ISDN E1 (Euro ISDN) Configuration Worksheet

Use the worksheet below to collect the information that may be required to complete the configuration of your DialFire PTE adapter within your operating system environment.

Note Not all operating systems support all parameters.

Note The parameters on this page are for ISDN E1 (Euro ISDN).

Parameter

 

 

Value

 

 

 

 

Line Type

E1

 

 

 

 

 

Framing

[ ] CEPT with CRC4

[ ] CEPT without CRC4

 

 

 

Coding

[ ] HDB3 [ ] AMI

 

 

 

 

Signaling

[ ] ETSI (Euro ISDN)

[ ] None

 

 

Leased Time Slots

List which, if any, E1 time slots are leased:

 

 

Modem Nationality

Enter the country in which the PTE adapter will be operated:

 

 

Before You Install the DialFire

Order the ISDN Line

RAS B4ST Adapter…

If you do not have an ISDN line installed, you need to contact your tele-

.

phone company and order a Basic Rate ISDN line (2B+D) with the follow-

 

 

ing recommended configuration:

 

 

Note If your telephone company supports either of the

 

 

following ISDN Ordering Codes, request that your

 

 

ISDN line be configured to one of them.

 

EZ-ISDN 1 (Preferred)

 

Capability S

 

 

If your telephone company does not support either of these Ordering

 

Codes, request the following ISDN line configuration:

 

Switch Type: National ISDN 1 (preferred), ETSI, AT&T 5ESS, or Nortel

 

 

DMS 100

 

 

ISDN Basic Rate Interface (BRI) service (2B+D)

 

2 B channels, D channel for signaling only (no D channel packet data)

 

Circuit Switched data and voice (CSD/CSV) on each channel

 

Dynamic TEI

 

 

Multipoint bus configuration

 

Terminal type A (AT&T Custom switch only)

 

No EKTS or special services or features

 

*You must select a long distance carrier and forward your choice, along with the Ordering

 

Code or line configuration, to your telephone company

 

 

 

 

After completing the worksheet, go to section chapter 3, “Installing the Model 2977 adapter” on page 29.

24

DialFire PTE ISDN E1 (Euro ISDN) Configuration Worksheet

Image 24
Contents DialFire Remote Access Server Patton Electronics Company, Inc Contents Contents Model 2977 DialFire RAS User Guide Using the Viewer Contents Model 2977 DialFire RAS User Guide Radio and TV Interference Industry Canada NoticeFCC Information DialFire B4/ST RAS FCC Part 68 Compliance Statement CE NoticeCompliance Information Model 2977 DialFire RAS User Guide Audience StructurePrecautions Typographical conventions used in this documentGeneral conventions Mouse conventions Typographical conventions used in this document Chapter contents DialFire Model 2977 RAS AdaptersIntroduction Model 2977 DialFire RAS overviewModel 2977/B4 DialFire BRI RAS Model 2977 DialFire T1/E1 RASSupported Operating Systems MicrosoftPreparation Completing a configuration worksheet DialFire Basic BRI Configuration Worksheet Patton Electronics DialFire Channelized T1, Short-Haul Configuration Worksheet DialFire PTE Isdn E1 Euro Isdn Configuration Worksheet Order the Isdn LineNone Interface ID for Port 48 PT2 Only 127 Leased Time Slots Before You Install DialFire Isdn T1 PRI, Short-Haul Configuration Worksheet Request the following Isdn line configuration Installing the Model 2977 adapter Model 2977 B4 ST adapter installation Determining your line termination requirementsInstalling the DialFire RAS B4ST Adapter DialFire BRI connectors and line-terminating DIP switchModel 2977 B4 U adapter installation Replace the computer’s coverDialFire BRI connectors Model 2977 PE1 PE2 adapter installation PE1 & PE2 Connector LocationsModel 2977 PT1 PT2 adapter installation PT1 & PT2 Connector LocationsModel 2977 daughter board installation Parts ListInstallation Model 2977 daughter board installation Plated-through holes Spacers Screws Mating Connectors Driver installation Configuration Driver installation and configuration Driver installation for the Windows 2000 operating system ProcedureSupported Products RequirementsInstalling the Driver Upgrading the DriverDriver installation for the Windows XP operating system Additional Notes Configuring Incoming Dial-up Networking ConnectionsConfiguring Outgoing Dial-up Networking Connections Changing Adapter PropertiesChanging Phone and Modem Options Uninstalling the Driver Using the Windows TroubleshooterInstalling the Driver CD Installing the Driver Downloaded Installing the MS Loopback AdapterConfiguring the Adapter First Time Changing the Adapter ConfigurationConfiguring RAS Ports Configuring RAS Dial-in Permissions Configuring Dial-up Networking Connections Configuring Modems on COM PortsChanging Serial Port Names Page Using the Viewer About Patton View Starting Patton ViewOperation and shutdown Activating the Model De-activating the Model
Related manuals
Manual 59 pages 22.92 Kb