Patton electronic 2977 manual Conﬁguring Outgoing Dial-up Networking Connections

Page 45

Model 2977 DialFire RAS User Guide	4 • Driver installation and configuration

Conﬁguring Outgoing Dial-up Networking Connections

Use this procedure to conﬁgure outgoing Dial-up Networking connections from your server to other systems. You should have already installed the Patton adapter and device driver.

Procedure

1.From the Start menu, choose Settings > Network and Dial-up Connections.

2.Choose Make New Connection to start the Network Connection Wizard.

3.Choose Dial-up to private network and complete the wizard.

4.Upon completion of the wizard, choose Properties if you wish to conﬁgure dialing rules (such as what

number to dial to get an outside line) or to add alternate phone numbers to try if the primary number is busy.

Changing Adapter Properties

Use this procedure to change the conﬁguration of an installed adapter.

Procedure

1.From the Start menu, choose Settings > Control Panel > System > Hardware > Device Manager.

2.From the displayed list, choose DialFire RAS as your network adapter.

3.Choose the Patton adapter you wish to conﬁgure.

4.From the Action menu, choose Properties > Advanced.

5.Conﬁgure the adapter as necessary.

6.If you changed the hardware resources from the default settings, Windows may notify you to restart the

system to complete the conﬁguration.

If you left the hardware resources at their default values, the adapter is ready to use without restarting the system.

Changing Phone and Modem Options

Use this procedure once you have installed and conﬁgured the driver and now want to change the conﬁgura- tion.

Phone and modem options that can be set with this procedure include:

•Maximum Port Speed

•Speaker Volume

•Dial Control

•Wait for tone before dialing

•Extra Initialization Commands

Procedure

1.From the Start menu, choose Settings > Control Panel > Phone and Modem Options > Modems.

2.Choose a Patton modem device to conﬁgure.

Driver installation for the Windows 2000 operating system

45

Image 45

Contents DialFire Remote Access Server Patton Electronics Company, Inc Contents Contents Model 2977 DialFire RAS User Guide Using the Viewer Contents Model 2977 DialFire RAS User Guide Radio and TV Interference Industry Canada NoticeFCC Information DialFire B4/ST RAS CE Notice FCC Part 68 Compliance StatementCompliance Information Model 2977 DialFire RAS User Guide Structure AudiencePrecautions Typographical conventions used in this documentGeneral conventions Mouse conventions Typographical conventions used in this document DialFire Model 2977 RAS Adapters Chapter contentsModel 2977 DialFire RAS overview IntroductionModel 2977 DialFire T1/E1 RAS Model 2977/B4 DialFire BRI RASMicrosoft Supported Operating SystemsPreparation Completing a conﬁguration worksheet DialFire Basic BRI Conﬁguration Worksheet Patton Electronics DialFire Channelized T1, Short-Haul Conﬁguration Worksheet Order the Isdn Line DialFire PTE Isdn E1 Euro Isdn Conﬁguration WorksheetNone Interface ID for Port 48 PT2 Only 127 Leased Time Slots Before You Install DialFire Isdn T1 PRI, Short-Haul Conﬁguration Worksheet Request the following Isdn line conﬁguration Installing the Model 2977 adapter Determining your line termination requirements Model 2977 B4 ST adapter installationDialFire BRI connectors and line-terminating DIP switch Installing the DialFire RAS B4ST AdapterReplace the computer’s cover Model 2977 B4 U adapter installationDialFire BRI connectors PE1 & PE2 Connector Locations Model 2977 PE1 PE2 adapter installationPT1 & PT2 Connector Locations Model 2977 PT1 PT2 adapter installationModel 2977 daughter board installation Parts ListInstallation Model 2977 daughter board installation Plated-through holes Spacers Screws Mating Connectors Driver installation Conﬁguration Driver installation and configuration Procedure Driver installation for the Windows 2000 operating systemSupported Products RequirementsUpgrading the Driver Installing the DriverDriver installation for the Windows XP operating system Conﬁguring Incoming Dial-up Networking Connections Additional NotesConﬁguring Outgoing Dial-up Networking Connections Changing Adapter PropertiesChanging Phone and Modem Options Uninstalling the Driver Using the Windows TroubleshooterInstalling the Driver CD Installing the MS Loopback Adapter Installing the Driver DownloadedConﬁguring the Adapter First Time Changing the Adapter ConﬁgurationConﬁguring RAS Ports Conﬁguring RAS Dial-in Permissions Conﬁguring Modems on COM Ports Conﬁguring Dial-up Networking ConnectionsChanging Serial Port Names Page Using the Viewer Starting Patton View About Patton ViewOperation and shutdown De-activating the Model Activating the Model

Related manuals

Manual 59 pages 22.92 Kb