Configuration, LED Status Monitors | Patton electronic 2135 instruction

5.0 CONFIGURATION

All configuration is done through software auto-detection for the Model 2135. Once you have configured your mux or other equipment to be connected to the 2135, the unit is ready for operation. Observe that the serial port of the 2135 is configured as a DTE and must con- nect to a DCE.

The LAN port also requires no configuration to connect to a 10BaseT Ethernet.

Note: The V.35 Interface is configured as a DTE. The 2135 will transmit and receive data to and from the DCE, based on the speed of the clocks received from the DCE.

On the LAN side interface, data is sent and received in burst mode at 10Mbps.

5.1 LED STATUS MONITORS

The 2135 uses two LEDs on the Ethernet connection side. A green LED indicates that link connection to the network is established. The yellow LED displays status codes (See section 5.1.2 for status code information).

Seven, low power, LEDs located on the top of the 2135 case indi- cate POWER and V.35 signal activity.

5.1.1 LAN side LEDs

The Model 2135 features two LAN LEDs that monitor general operation status and the 10BaseT twisted pair link integrity. Figure 4 shows the LEDs located at the rear of the Model 2135. Following Figure 4 is a description of each LED function. Figure 5 shows the LEDs located on the top of the Model 2135.

RJ-45 Jack, 10BaseT connection

Yellow LED,

Power Status

Jack

Green LED, link integrity

Figure 4. 2135 rear view

5.1.2 LED Descriptions

The status LED blinks yellow from one to eleven times to indicate system status. Each pulse pattern is separated by a 2 second "off " peri- od. Greater pulse patterns have higher priority (buffer saturation has greater priority than an empty MAC table).

Valid system statuses are:

1 pulse		=	system status ok
2 pulses		=	No MAC entries in the MAC address table
3 pulses		=	Clear to send (CTS) or Carrier Detect (DCD) from
base unit are not asserted
4	pulses	=	IMRC2/IA buffer is saturated
5	pulses	=	WAN receive frame(s) too large
6	pulses	=	WAN receive frame(s) not Octet aligned
7	pulses	=	WAN receive frame(s) aborted
8	pulses	=	Detected WAN receive frame(s) with bad CRC
9	pulses	=	Detected LAN receive frame(s) too large
10 pulses		=	Detected LAN receive frame(s) not Octet aligned
11 pulses		=	Detected LAN receive frame(s) with bad CRC

After a status code is displayed eight times and the associated con- dition is removed, the status code will no longer appear.

The link LED glows green to indicate link integrity on the 10BaseT twisted pair line.

5.1.3 Power and DCE/DTE Interface LEDs

Seven LEDs indicate POWER and DTE/DCE activity on the front of the 2135.

2135 specifications

The Patton Electronics 2135 is a versatile, high-performance VoIP gateway designed to facilitate seamless communication in both home and enterprise environments. This exceptional device offers a range of features tailored for reliable voice transmission while supporting various legacy systems and modern IP infrastructures.

One of the main features of the Patton 2135 is its robust support for multiple analog telephone and fax machines. Equipped with FXS ports, this gateway allows traditional telephony devices to connect to VoIP services, making the transition from conventional phone systems to VoIP easy and efficient. This is particularly important for businesses looking to modernize their communication platforms without expensive overhauls of existing hardware.

The 2135 incorporates advanced technologies, including SIP (Session Initiation Protocol) for call management, which provides flexibility and compatibility with a wide range of VoIP services. The device also supports various voice codecs, ensuring high-quality audio during calls while optimizing bandwidth usage. This features a built-in echo cancellation and noise suppression technology, which enhances voice clarity, even in challenging network conditions.

Another critical characteristic of the Patton 2135 is its ease of use and configurability. The device includes a user-friendly web-based interface for setup and management, enabling users to quickly configure settings according to their needs. Additionally, it supports remote management protocols, which allow for centralized administration and troubleshooting across multiple sites, further increasing its appeal for enterprises with distributed operations.

Security is a top priority in today's interconnected world, and the Patton 2135 addresses this with support for various encryption protocols including SRTP (Secure Real-Time Transport Protocol) and TLS (Transport Layer Security). These features ensure that voice communication remains safe and private, protecting sensitive information from potential breaches.

Lastly, the compact design of the Patton 2135 makes it easy to deploy in a variety of environments, from small office setups to larger organizational infrastructures. With its combination of advanced technology, user-friendly management options, and robust security features, the Patton Electronics 2135 VoIP gateway stands out as an ideal choice for anyone looking to enhance their communication capabilities. Whether for small businesses or larger enterprises, it offers efficient, scalable, and secure solutions to meet modern communication needs.