TP-Link TL-WR1042ND manual FCC Statement

Page 3

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference.

This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

FCC RF Radiation Exposure Statement:

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.

“To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.”

Image 3

Contents TL-WR1042ND Copyright & Trademarks FCC Statement Country Restriction Reason/remark CE Mark WarningKorea Warning Statements Yang Hongliang Product Manager of International Business Product Description 300Mbps Wireless N Gigabit RouterContents USB Settings III Package Contents Incredible Speed Flexible Access ControlSimple Installation Overview of the RouterConventions Main FeaturesPanel Layout Front PanelName Status Indication Rear Panel ¾ ResetTL-WR1042ND300Mbps Wireless N Gigabit Router Installation Environment Requirements Connecting the RouterSystem Requirements TL-WR1042ND300Mbps Wireless N Gigabit Router TCP/IP Configuration Quick Installation GuidePlease check the connection following these steps Quick Installation Guide3Login the Router Choose WAN Connection Type Quick Setup MAC Clone 10 Find MAC Address 12 Quick Setup Wireless 13 Quick Setup Finish PSK Password You can enter Ascii or Hexadecimal charactersStatus LoginWPS Quick SetupUse the Wi-Fi Protected Setup Button Wi-Fi Protected Setup functionIII. Enter the Router’s PIN on your client device II. Enter the client device’s PIN on the Router1 WAN NetworkWAN Static IP WAN PPPoE TL-WR1042ND300Mbps Wireless N Gigabit Router PPPoE Advanced Settings 10 WAN BigPond Cable NSW / ACT nsw.bigpond.net.au11 WAN -L2TP TL-WR1042ND300Mbps Wireless N Gigabit Router 12 WAN -PPTP 13 LAN 2 LAN14 MAC Address Clone MAC CloneWireless Settings WirelessTL-WR1042ND300Mbps Wireless N Gigabit Router Wireless Security TL-WR1042ND300Mbps Wireless N Gigabit Router Encryption You can select either Automatic, or Tkip or AES Wireless MAC Filtering 21 Wireless MAC address Filtering To modify or delete an existing entry Wireless Advanced Wireless Statistics Dhcp Dhcp SettingsAddress Reservation Dhcp Clients List28 Address Reservation To Reserve IP addressesStorage Sharing USB SettingsRouter can automatically locate new USB drive FTP Server TL-WR1042ND300Mbps Wireless N Gigabit Router TL-WR1042ND300Mbps Wireless N Gigabit Router Media Server TL-WR1042ND300Mbps Wireless N Gigabit Router Print Server 43 Pint Server SettingTo add a new user account, please follow the steps below User AccountsTL-WR1042ND300Mbps Wireless N Gigabit Router Virtual Servers Forwarding48 Add or Modify a Virtual Server Entry To setup a virtual server entryTo add a new rule, follow the steps below Port Triggering50 Add or Modify a Triggering Entry Once the Router is configured, the operation is as follows3 DMZ UPnPTo assign a computer or server to be a DMZ server Security 52 UPnP Setting54 Basic Security Basic SecurityAdvanced Security TL-WR1042ND300Mbps Wireless N Gigabit Router 56 Local Management Local Management57 Remote Management Remote ManagementTo add a new entry, please follow the steps below Parental Control59 Add or Modify Parental Control Entry 60 Parental Control Settings Access ControlRule 62 Access Control Rule ManagementThere are two methods to add a new rule Method One 63 Quick Setup Create a Host EntryTL-WR1042ND300Mbps Wireless N Gigabit Router 66 Quick Setup Create an Internet Access Control Entry Method Two 67 Add Internet Access Control EntryHost 68 Host Settings69 Add or Modify a Host Entry Target 71 Target Settings72 Add or Modify an Access Target Entry To add a new schedule, follow the steps below Schedule75 Advanced Schedule Settings Advanced Routing Static Routing ListTo add static routing entries System Routing Table Other configurations for the entriesControl Settings Bandwidth ControlRules List 82 Bandwidth Control Rules List Binding Settings 15 IP & MAC Binding SettingTo find an existing entry, follow the steps below To add IP & MAC Binding entries, follow the steps belowARP List Dynamic DNSComexe.cn Ddns To set up for DDNS, follow these instructionsDyndns.org Ddns 90 Dyndns.org Ddns Settings92 The System Tools menu System ToolsTo set time automatically Time SettingDiagnostic 95 Diagnostic Results Firmware Upgrade96 Firmware Upgrade Factory Defaults97 Restore Factory Default Backup & RestorePassword Reboot101 System Log System LogTL-WR1042ND300Mbps Wireless N Gigabit Router 103 Statistics StatisticsStatistics Table TL-WR1042NDAppendix a FAQ Figure A-3 MAC Clone Want to use Netmeeting, what do I need to do?Figure A-5 Add or Modify a Virtual server Entry Want to build a WEB Server on the LAN, what should I do? Figure A-7 Basic SecurityFigure A-9 Virtual Servers Wireless stations cannot connect to the Router105 Install TCP/IP component Appendix B Configuring the PCsFigure B-2 Figure B-3 Wireless GeneralEnvironmental and Physical Appendix D Glossary 111