TP-Link manual TL-WA730RE 150Mbps Wireless N Range Extender User Guide

Page 13

TL-WA730RE150Mbps Wireless N Range Extender User Guide

RESET: The Reset button is used to restore the AP’s factory default settings. There are two ways to reset the Access Point’s factory defaults:

zMethod one: With the AP powered on, use a pin to press and hold the Reset button (about 5 seconds) until the System LED becomes quick-flash from slow-flash. And then release the button and wait the AP to reboot to its factory default settings.

zMethod two: Restore the default settings from “System Tools > Factory Defaults” of the AP's Web-based management page.

Wireless antenna: The external antenna is used to transmit and receive wireless data.

)Note:

Ensure the Range Extender is powered on before it restarts completely.

5

Image 13

Contents Rev 2.0.0 TL-WA730RE 150Mbps Wireless N Range ExtenderAll rights reserved COPYRIGHT & TRADEMARKSFCC RF Radiation Exposure Statement FCC STATEMENTCE Mark Warning Canadian Compliance Statement Safety InformationIndustry Canada Statement Korea Warning StatementsThis product can be used in the following countries Product Description 150Mbps Wireless N Range Extender DECLARATION OF CONFORMITYThe product carries the CE Mark ETSI EN 300 328 V1.7.1Package Contents CONTENTSHardware Installation Chapter 3 Quick Installation GuideAppendix C Troubleshooting Appendix B Factory DefaultsAppendix D Specifications Appendix A Application ExampleTL-WA730RE Package Contents1.1 Product Overview Chapter 1 Introduction1.2 Conventions TL-WA730RE 150Mbps Wireless N Range Extender User GuideFeatures 1.3 Main Features1.4 Appearance Benefits1.4.2 The Rear Panel Ensure the Range Extender is powered on before it restarts completely 2.3 Connecting the Device Chapter 2 Hardware Installation2.1 Before You Begin 2.2 Basic Requirements1. Connect the Cable or DSL modem to a Router 3.1 Quick Setup Chapter 3 Quick Installation GuideFigure 3-2 Login Windows Figure 3-4 Operation Mode Figure 3-6 AP List Figure 3-7 Wireless Settings - Access Point mode Figure 3-9 Quick Setup - Finish Figure 3-11 Quick Setup - Finish 4.1 Login Chapter 4 Configure the Device4.2 Status 4.4 Operation Mode 4.3 Quick Setup4.5 WPS I. By PBC To add a new deviceMethod One TL-WA730RE 150Mbps Wireless N Range Extender User Guide TL-WA730RE 150Mbps Wireless N Range Extender User Guide TL-WA730RE 150Mbps Wireless N Range Extender User Guide 4.6 Network 4.7 Wireless4.7.1 Wireless Settings ¾ Region - Please select the right region from the drop-down list 4.7.2 Wireless Security 3 WPA2-Personal - WPA version 1 Repeater Range ExtenderWEP Key Format - You can select ASCII or Hexadecimal format. ASCII format stands for any combination of keyboard characters in the specified length. Hexadecimal format stands for any combination of hexadecimal digits 0-9, a-f, A-F in the specified length 2 Access Point 4.7.3 Wireless MAC Filtering To add a MAC Address Filtering entry, follow these instructions To set up an entry, follow these instructionsTo modify or delete an existing entry 150Mbps Wireless N Range Extender User Guide 4.7.4 Wireless Advanced4.7.6 Throughput Monitor 4.7.5 Antenna Alignment4.8 DHCP 4.7.7 Wireless Statistics4.8.1 DHCP Settings 4.8.3 Address Reservation 4.8.2 DHCP Clients ListTo Reserve IP addresses 4.9 System ToolsTo modify A Reserved IP address To delete all Reserved IP addresses 1. Click Clear All4.9.1 SNMP 4.9.2 Time Settings ¾ To set time manually 4.9.3 Diagnostic¾ For automatic time synchronization Figure 4-28 Diagnostic 4.9.4 Ping Watch Dog 4.9.5 Firmware Upgrade 4.9.7 Backup & Restore 4.9.6 Factory DefaultsTo upgrade the devices firmware, follow these instructions To restore the devices configuration, follow these instructions 4.9.8 Reboot4.9.10 System Log 4.9.9 PasswordFigure 4-36 System Log 4.9.11 Statistics ¾ Total ¾ Statistics Table¾ Current ¾ ModifyAppendix A Application Example 3 Right-click the wireless connection icon “” on the screen of the PC and then select View Available Wireless Networks TL-WA730RE 150Mbps Wireless N Range Extender User Guide Default Value Appendix B Factory DefaultsCommon Default Settings WirelessT2. What can I do if I forget my password? Appendix C Troubleshooting3 Right-click Local Area Connection, and Click Properties 2 Click Change adapter settings4 Double-click Internet Protocol Version 4 TCP/IPv4 TL-WA730RE 150Mbps Wireless N Range Extender User Guide General Appendix D SpecificationsPhysical and Environment Appendix E Glossary TL-WA730RE 150Mbps Wireless N Range Extender User Guide

Related manuals

Manual 64 pages 33.88 Kb