TP-Link manual DHCP Settings, TL-WA730RE 150Mbps Wireless N Range Extender User Guide

Page 43
4.8.1 DHCP Settings

TL-WA730RE150Mbps Wireless N Range Extender User Guide

Figure 4-21 The DHCP menu

4.8.1 DHCP Settings

Selecting DHCP > DHCP Settings will enable you to set up the AP as a DHCP (Dynamic Host Configuration Protocol) server, which provides the TCP/IP configuration for all the PCs that are connected to the system on the LAN. The DHCP Server can be configured on the page (shown as Figure 4-22):

Figure 4-22 DHCP Settings

¾DHCP Server - Selecting the radio button before Disable/Enable will disable/enable the DHCP server on your AP. The default setting is Enable. If you disable the Server, you must have another DHCP server within your network or else you must manually configure the computer.

¾Start IP Address - This field specifies the first address in the IP Address pool. 192.168.0.100 is the default start IP address.

¾End IP Address - This field specifies the last address in the IP Address pool. 192.168.0.199 is the default end IP address.

¾Address Lease Time - Enter the amount of time for the PC to connect to the AP with its current assigned dynamic IP address. The time is measured in minutes. After the time is up, the PC will be automatically assigned a new dynamic IP address. The range of the time is 1 ~ 2880 minutes. The default value is 120 minutes.

¾Default Gateway (optional) - Enter the IP address of the gateway for your LAN. The factory default setting is 0.0.0.0.

¾Default Domain (optional) - Enter the domain name of the your DHCP server. You can leave the field blank.

35

Image 43
Contents Rev 2.0.0 TL-WA730RE 150Mbps Wireless N Range ExtenderAll rights reserved COPYRIGHT & TRADEMARKSFCC RF Radiation Exposure Statement FCC STATEMENTCE Mark Warning Korea Warning Statements Safety InformationCanadian Compliance Statement Industry Canada StatementThis product can be used in the following countries ETSI EN 300 328 V1.7.1 DECLARATION OF CONFORMITYProduct Description 150Mbps Wireless N Range Extender The product carries the CE MarkChapter 3 Quick Installation Guide CONTENTSPackage Contents Hardware InstallationAppendix A Application Example Appendix B Factory DefaultsAppendix C Troubleshooting Appendix D SpecificationsTL-WA730RE Package ContentsTL-WA730RE 150Mbps Wireless N Range Extender User Guide Chapter 1 Introduction1.1 Product Overview 1.2 ConventionsBenefits 1.3 Main FeaturesFeatures 1.4 Appearance1.4.2 The Rear Panel Ensure the Range Extender is powered on before it restarts completely 2.2 Basic Requirements Chapter 2 Hardware Installation2.3 Connecting the Device 2.1 Before You Begin1. Connect the Cable or DSL modem to a Router 3.1 Quick Setup Chapter 3 Quick Installation GuideFigure 3-2 Login Windows Figure 3-4 Operation Mode Figure 3-6 AP List Figure 3-7 Wireless Settings - Access Point mode Figure 3-9 Quick Setup - Finish Figure 3-11 Quick Setup - Finish 4.1 Login Chapter 4 Configure the Device4.2 Status 4.4 Operation Mode 4.3 Quick Setup4.5 WPS I. By PBC To add a new deviceMethod One TL-WA730RE 150Mbps Wireless N Range Extender User Guide TL-WA730RE 150Mbps Wireless N Range Extender User Guide TL-WA730RE 150Mbps Wireless N Range Extender User Guide 4.6 Network 4.7 Wireless4.7.1 Wireless Settings ¾ Region - Please select the right region from the drop-down list 4.7.2 Wireless Security 3 WPA2-Personal - WPA version 1 Repeater Range ExtenderWEP Key Format - You can select ASCII or Hexadecimal format. ASCII format stands for any combination of keyboard characters in the specified length. Hexadecimal format stands for any combination of hexadecimal digits 0-9, a-f, A-F in the specified length 2 Access Point 4.7.3 Wireless MAC Filtering To add a MAC Address Filtering entry, follow these instructions To set up an entry, follow these instructionsTo modify or delete an existing entry 150Mbps Wireless N Range Extender User Guide 4.7.4 Wireless Advanced4.7.6 Throughput Monitor 4.7.5 Antenna Alignment4.8 DHCP 4.7.7 Wireless Statistics4.8.1 DHCP Settings 4.8.3 Address Reservation 4.8.2 DHCP Clients ListTo delete all Reserved IP addresses 1. Click Clear All 4.9 System ToolsTo Reserve IP addresses To modify A Reserved IP address4.9.1 SNMP 4.9.2 Time Settings ¾ To set time manually 4.9.3 Diagnostic¾ For automatic time synchronization Figure 4-28 Diagnostic 4.9.4 Ping Watch Dog 4.9.5 Firmware Upgrade 4.9.7 Backup & Restore 4.9.6 Factory DefaultsTo upgrade the devices firmware, follow these instructions To restore the devices configuration, follow these instructions 4.9.8 Reboot4.9.10 System Log 4.9.9 PasswordFigure 4-36 System Log 4.9.11 Statistics ¾ Modify ¾ Statistics Table¾ Total ¾ CurrentAppendix A Application Example 3 Right-click the wireless connection icon “” on the screen of the PC and then select View Available Wireless Networks TL-WA730RE 150Mbps Wireless N Range Extender User Guide Wireless Appendix B Factory DefaultsDefault Value Common Default SettingsT2. What can I do if I forget my password? Appendix C Troubleshooting3 Right-click Local Area Connection, and Click Properties 2 Click Change adapter settings4 Double-click Internet Protocol Version 4 TCP/IPv4 TL-WA730RE 150Mbps Wireless N Range Extender User Guide General Appendix D SpecificationsPhysical and Environment Appendix E Glossary TL-WA730RE 150Mbps Wireless N Range Extender User Guide
Related manuals
Manual 64 pages 33.88 Kb