TP-Link TL-WN822N manual 300Mbps High Gain Wireless N USB Adapter

Page 21

Manual background

TL-WN822N

300Mbps High Gain Wireless N USB Adapter

Figure 3-8

Figure 3-9

Method Two:

Open TWCU and click QSS tab. Select Push the button on my access point or wireless router and then click Connect.

Figure 3-10

13

Image 21

Contents TL-WN822N 300Mbps High Gain Wireless N USB AdapterCOPYRIGHT & TRADEMARKS FCC RF Radiation Exposure Statement FCC STATEMENTNational Restrictions CE Mark WarningCountry RestrictionIndustry Canada Statement Korea Warning StatementsNCC Notice Page DECLARATION OF CONFORMITY The product carries the CE MarkShennan Rd, Nanshan, Shenzhen, China CONTENTS Conventions Package ContentsTL-WN822N 300Mbps High Gain Wireless N USB Adapter Note1.2 Main Features Chapter 1 Introduction1.1 Product Overview 1.3 Hardware Overview StatusWorking Status Chapter 2 Installation 2.1 Hardware Installation2.2 Software Installation TL-WN822N 300Mbps High Gain Wireless N USB Adapter TL-WN822N 300Mbps High Gain Wireless N USB Adapter6. The utility and drivers will install. This may take 1~2 minutes 5. Click Install to continue the setup7. After all the steps above, you will see the screen below. Click Finish to complete the setup 3.1 To connect using TWCU TP-LINK Wireless Configuration Utility Chapter 3 Connect to a Wireless Network3. If word None appears behind the SSID, this means the network to be connected is not security-enabled and you can connect to the network without entering a key. To prevent outside intrusion and safeguard your network, it is strongly recommended that you set a password to your router or access point 4. You have now successfully connected to your network. Click Close to enjoy the Internet 3.2.1 PBC Push Button Configuration method 3.2 To connect using QSSTL-WN822N 3.2.2 PIN method 2. The adapter will be connecting to the target network TL-WN822N 300Mbps High Gain Wireless N USB Adapter 3.3.1 In Windows 3.3 To connect using Windows built-in wireless utility3. You have now successfully connected to the network 3.3.2 In Windows Vista1. Open the wireless utility by right-clicking on the wireless computer icon in your system tray as shown in the figure below. Select Connect to a network 3.3.3 In Windows XP TL-WN822N 2. Right-click on the wireless computer icon in your system tray lower-right corner. Select View Available Wireless Networks 4.1 Profile Chapter 4 ManagementThe following items can be found on the screen 4.1.3 Delete a profile 4.1.2 Modify a profile4.2 Advanced 4.3 About Chapter 5 AP Mode  SoftAP mode Select to enable or disable the function Chapter 6 Uninstall Software 6.1 Uninstall the utility software from your PC6.2 Uninstall the driver software from your PC Figure 6-2 Device Manager 300Mbps High Gain Wireless N USB Adapter Appendix A SpecificationsOperation Temperature 0~40 32~104Appendix B Glossary  Spread Spectrum - Spread Spectrum technology is a wideband radio frequency technique developed by the military for use in reliable, secure, mission-critical communications systems. It is designed to trade off bandwidth efficiency for reliability, integrity, and security. In other words, more bandwidth is consumed than in the case of narrowband transmission, but the trade off produces a signal that is, in effect, louder and thus easier to detect, provided that the receiver knows the parameters of the spread-spectrum signal being broadcast. If a receiver is not tuned to the right frequency, a spread-spectrum signal looks like background noise. There are two main alternatives, Direct Sequence Spread Spectrum DSSS and Frequency Hopping Spread Spectrum FHSS

Related manuals

Manual 49 pages 48.03 Kb