TP-Link manual In Windows Vista, TL-WN822N 300Mbps High Gain Wireless N USB Adapter

Page 26

3.You have now successfully connected to the network.

TL-WN822N300Mbps High Gain Wireless N USB Adapter

Figure 3-19

3.You have now successfully connected to the network.

Figure 3-20

3.3.2 In Windows Vista

Windows Vista users may use the built-in wireless utility. Follow the steps below.

18

Image 26

Contents 300Mbps High Gain Wireless N USB Adapter TL-WN822NCOPYRIGHT & TRADEMARKS FCC STATEMENT FCC RF Radiation Exposure StatementCountry CE Mark WarningNational Restrictions RestrictionNCC Notice Industry Canada StatementKorea Warning Statements Page Shennan Rd, Nanshan, Shenzhen, China DECLARATION OF CONFORMITYThe product carries the CE Mark CONTENTS TL-WN822N 300Mbps High Gain Wireless N USB Adapter Package ContentsConventions Note1.1 Product Overview 1.2 Main FeaturesChapter 1 Introduction Working Status 1.3 Hardware OverviewStatus 2.2 Software Installation Chapter 2 Installation2.1 Hardware Installation TL-WN822N 300Mbps High Gain Wireless N USB Adapter 300Mbps High Gain Wireless N USB Adapter TL-WN822N5. Click Install to continue the setup 6. The utility and drivers will install. This may take 1~2 minutes7. After all the steps above, you will see the screen below. Click Finish to complete the setup Chapter 3 Connect to a Wireless Network 3.1 To connect using TWCU TP-LINK Wireless Configuration Utility3. If word None appears behind the SSID, this means the network to be connected is not security-enabled and you can connect to the network without entering a key. To prevent outside intrusion and safeguard your network, it is strongly recommended that you set a password to your router or access point 4. You have now successfully connected to your network. Click Close to enjoy the Internet 3.2 To connect using QSS 3.2.1 PBC Push Button Configuration method300Mbps High Gain Wireless N USB Adapter 3.2.2 PIN method 2. The adapter will be connecting to the target network TL-WN822N 300Mbps High Gain Wireless N USB Adapter 3.3 To connect using Windows built-in wireless utility 3.3.1 In Windows3.3.2 In Windows Vista 3. You have now successfully connected to the network1. Open the wireless utility by right-clicking on the wireless computer icon in your system tray as shown in the figure below. Select Connect to a network 3.3.3 In Windows XP 300Mbps High Gain Wireless N USB Adapter 2. Right-click on the wireless computer icon in your system tray lower-right corner. Select View Available Wireless Networks Chapter 4 Management 4.1 ProfileThe following items can be found on the screen 4.1.2 Modify a profile 4.1.3 Delete a profile4.2 Advanced 4.3 About Chapter 5 AP Mode  SoftAP mode Select to enable or disable the function 6.2 Uninstall the driver software from your PC Chapter 6 Uninstall Software6.1 Uninstall the utility software from your PC Figure 6-2 Device Manager Operation Temperature Appendix A Specifications300Mbps High Gain Wireless N USB Adapter 0~40 32~104Appendix B Glossary  Spread Spectrum - Spread Spectrum technology is a wideband radio frequency technique developed by the military for use in reliable, secure, mission-critical communications systems. It is designed to trade off bandwidth efficiency for reliability, integrity, and security. In other words, more bandwidth is consumed than in the case of narrowband transmission, but the trade off produces a signal that is, in effect, louder and thus easier to detect, provided that the receiver knows the parameters of the spread-spectrum signal being broadcast. If a receiver is not tuned to the right frequency, a spread-spectrum signal looks like background noise. There are two main alternatives, Direct Sequence Spread Spectrum DSSS and Frequency Hopping Spread Spectrum FHSS

Related manuals

Manual 49 pages 48.03 Kb