TP-Link TL-WN822N manual Industry Canada Statement, Korea Warning Statements, NCC Notice

Page 5

Industry Canada Statement

This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions:

(1)This device may not cause harmful interference, and

(2)This device must accept any interference received, including interference that may cause undesired operation.

IMPORTANT NOTE:

Radiation Exposure Statement:

This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Ce dispositif est conforme à la norme CNR-210 d’Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes:

(1)Le dispositif ne doit pas produire de brouillage préjudiciable, et

(2)Ce dispositif doit accepter tout brouillage reçu,y compris un brouillage susceptible de provoquer un fonctionnement indésirable.

NOTE IMPORTANTE:

Déclaration d’exposition aux radiations:

Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.

Korea Warning Statements

당해 무선설비는 운용중 전파혼신 가능성이 있음.

NCC Notice

經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自變更頻率、加大 功率或變更原設計之特性及功能。

低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時,應立即停用, 並改善至無干擾時方得繼續使用。前項合法通信,指依電信法規定作業之無線電通信。低功率射 頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。

Image 5
Contents TL-WN822N 300Mbps High Gain Wireless N USB AdapterCOPYRIGHT & TRADEMARKS FCC RF Radiation Exposure Statement FCC STATEMENTNational Restrictions CE Mark WarningCountry RestrictionNCC Notice Industry Canada StatementKorea Warning Statements Page Shennan Rd, Nanshan, Shenzhen, China DECLARATION OF CONFORMITYThe product carries the CE Mark CONTENTS Conventions Package ContentsTL-WN822N 300Mbps High Gain Wireless N USB Adapter Note1.1 Product Overview 1.2 Main FeaturesChapter 1 Introduction Working Status 1.3 Hardware OverviewStatus 2.2 Software Installation Chapter 2 Installation2.1 Hardware Installation TL-WN822N 300Mbps High Gain Wireless N USB Adapter TL-WN822N 300Mbps High Gain Wireless N USB Adapter6. The utility and drivers will install. This may take 1~2 minutes 5. Click Install to continue the setup7. After all the steps above, you will see the screen below. Click Finish to complete the setup 3.1 To connect using TWCU TP-LINK Wireless Configuration Utility Chapter 3 Connect to a Wireless Network3. If word None appears behind the SSID, this means the network to be connected is not security-enabled and you can connect to the network without entering a key. To prevent outside intrusion and safeguard your network, it is strongly recommended that you set a password to your router or access point 4. You have now successfully connected to your network. Click Close to enjoy the Internet 3.2.1 PBC Push Button Configuration method 3.2 To connect using QSSTL-WN822N 3.2.2 PIN method 2. The adapter will be connecting to the target network TL-WN822N 300Mbps High Gain Wireless N USB Adapter 3.3.1 In Windows 3.3 To connect using Windows built-in wireless utility3. You have now successfully connected to the network 3.3.2 In Windows Vista1. Open the wireless utility by right-clicking on the wireless computer icon in your system tray as shown in the figure below. Select Connect to a network 3.3.3 In Windows XP TL-WN822N 2. Right-click on the wireless computer icon in your system tray lower-right corner. Select View Available Wireless Networks 4.1 Profile Chapter 4 ManagementThe following items can be found on the screen 4.1.3 Delete a profile 4.1.2 Modify a profile4.2 Advanced 4.3 About Chapter 5 AP Mode  SoftAP mode Select to enable or disable the function 6.2 Uninstall the driver software from your PC Chapter 6 Uninstall Software6.1 Uninstall the utility software from your PC Figure 6-2 Device Manager 300Mbps High Gain Wireless N USB Adapter Appendix A SpecificationsOperation Temperature 0~40 32~104Appendix B Glossary  Spread Spectrum - Spread Spectrum technology is a wideband radio frequency technique developed by the military for use in reliable, secure, mission-critical communications systems. It is designed to trade off bandwidth efficiency for reliability, integrity, and security. In other words, more bandwidth is consumed than in the case of narrowband transmission, but the trade off produces a signal that is, in effect, louder and thus easier to detect, provided that the receiver knows the parameters of the spread-spectrum signal being broadcast. If a receiver is not tuned to the right frequency, a spread-spectrum signal looks like background noise. There are two main alternatives, Direct Sequence Spread Spectrum DSSS and Frequency Hopping Spread Spectrum FHSS
Related manuals
Manual 49 pages 48.03 Kb