Polycom 4300T manual Frame Relay Mode and Dlci

Page 37

Configuring the 4300T

Protocol

Display and set the T1 Layer 2 protocol. Supported protocols are:

•HDLC

•Cisco HDLC

•PPP

•ANSI (Frame Relay)

•CCITT (Frame Relay)

1.Select the desired T1 protocol.

2.Press Submit.

Frame Relay Mode and DLCI

When the Protocol is one of ANSI or CCITT, then additional Frame Relay configuration parameters are required.

The Frame Relay Mode is usually set to DTE for the customer premises.

The Frame Relay DLCI is set by the WAN provider and identifies the far-end device across the Frame Relay network. This DLCI can also be used to carry voice traffic only by enabling the Secondary DLCI for data.

Most installations will use a single DLCI for both voice and data traffic. However, in instances where the network will provide a different quality of service based on DLCI number it is desirable to place all voice traffic on one DLCI and then configure a second DLCI for data. In this case, the Secondary DLCI is configured as follows:

1.Select Network.

2.Select the T1 link next to the radio button to proceed to the T1 configuration page.

3.Select Enable in the Frame Relay Secondary Settings section of the page.

4.Enter the Secondary DLCI, IP Address, Network Mask and Gateway for the data traffic using the Secondary DLCI.

3 - 19

Image 37

Contents

User Guide V2IU 4300T Converged Network Appliance Trademark Information Contents User Guide V2IU 4300T Converged Network Appliance System Diagnostics Upgrading the 4300T Saving and Restoring the 4300T ConfigurationContents User Guide V2IU 4300T Converged Network Appliance Quality of Service T1 Wide Area Network WAN Access Router4300T Converged Network Appliance SecurityCall Quality Monitoring Feature SummaryFuture-proof Scalability LED Label Activity Description Front Panel LEDsBack Panel Power ConnectorErase Button Management console portEthernet WAN port T1/E1 WAN portUser Guide V2IU 4300T Converged Network Appliance Desktop Installation Physical InstallationWall-Mount Installation Administration of the 4300T Getting Started User Guide V2IU 4300T Converged Network Appliance Configuring the 4300T Configuration Guide For IP Centrex Applications Task Subtask Configure For IP Centrex Application? Configuration OutlineUser Guide V2IU 4300T Converged Network Appliance Configuration Guide For Station Side IP PBX Applications Configure For Station Configuration Guide For Trunk Side IP PBX Applications Task Subtask Configure For Trunk Side IP PBX Application? Configuration Guide For Hosted Video Applications Configure For Hosted Configuration Guide For Enterprise Video Applications Configure For Hosted Configure the LAN Interface System ConfigurationPress Submit Configuring the 4300T Modify an Existing Vlan Configuration Configure the WAN Interface User Guide V2IU 4300T Converged Network Appliance Frame Relay Mode and Dlci Configure the Dhcp Server Mask Select Dhcp Server Uncheck the Enable Dhcp Server checkbox Configure Hostname, Snmp and Remote Logging Disable Snmp Configure a local Hostname Change the Administration Password VoIP ConfigurationConfigure the VoIP ALG Performs a Tftp server relay function Configure VoIP Subnet Routing Enter a VoIP Subnet Route Configure IP Phones, IADs or Softphones NAT for Data Traffic Data Networking ConfigurationProtocolPublicIPAddress/netmask-portPrivateIPAddress-port Static IP routing Firewall Configuration Enable or disable the firewall Action Description Input format Traffic Management Configuration Enable Traffic Shaping Enable CAC Optionally enable priority IP addressesCloser Look at Traffic Management in the 4300T Upstream Traffic Management ClassifyingDownstream Traffic Management Key benefits and features of VoIP survivability VoIP Survivability ConfigurationHow survivability works Platform Support Configuring VoIP Survivability in V2IU AppliancesEnable VoIP Survivability Specify the number of digits to use for local dialing Configuring the 4300T Configure call processing server redundancy Configuring the 4300T User Guide V2IU 4300T Converged Network Appliance System Diagnostics Viewing Networking Information Viewing the ALG registration codeRouting Information Viewing Advanced System Information Passive Voice Call Monitoring Accessing Troubleshooting ToolsVerify Registered Voice and Video Devices Performing a Ping Test Restarting Networking Processes Ewn Command Saving and Restoring the 4300T ConfigurationCopy a Backup File to a Remote Tftp Server Create a Backup File and Save in Local FlashDownload a Backup File from a Remote Tftp Server List the Available Backup FilesDelete a Backup File User Guide V2IU 4300T Converged Network Appliance Upgrading the 4300T Upgrade Procedure for Software Revision 1.3.11 or LaterUser Guide V2IU 4300T Converged Network Appliance Appendix Troubleshooting TipsSpecifications Example Neighboring Path Navigator Gatekeeper supportCloud Configuration Neighboring Gatekeeper Neighbors Add Endpoints Path Navigator On the Path Navigator GK A, setup two Neighboring Gatekeeper Network Settings VoIP ALG H323 Settings Appendix Configuration -- Neighboring Gatekeeper -- Neighbors -- Add Network Settings VoIP ALG H323 settings Appendix V2IU C VoIP ALG H323 Settings User Guide V2IU 4300T Converged Network Appliance Appendix Endpoints Path Navigator Regulatory Notices Other Rights and Limitations Regulatory Notices Warranty and Warranty Exclusions Regulatory Notices Miscellaneous Regulatory Notices User Guide V2IU 4300T Converged Network Appliance Regulatory Notices User Guide V2IU 4300T Converged Network Appliance FCC Part 15 Notice Industry Canada IC Notice Warranty and Repair Service Center