TP-Link manual 5.9System Tools, Firmware, TL-R402M Cable/DSL Router User Guide

Page 42
To modify an existing entry:

TL-R402MCable/DSL Router User Guide

1. Enter the following data:

¾Destination IP Address - The Destination IP Address is the address of the network or host that you want to assign to a static route

¾Subnet Mask - The Subnet Mask determines which portion of an IP address is the network portion, and which portion is the host portion

¾Gateway - This is the IP address of the gateway device that allows for contact between the router and the network or host

2.Click the Enable checkbox.

3.Repeat steps 1-2 until you are finished.

4.If you are finished. Click the Save button to save it.

To modify an existing entry:

1.Modify the entry’s Destination IP Address, Subnet Mask and Gateway.

2.Click the Save button.

To delete an existing entry:

1.Select the entry as you desire and make all of its fields blank.

2.Click the Save button.

To delete all the entries:

1.Click the Clear All button.

2.Click the Save button.

Note:

You can set up to 8 entries.

5.9System Tools

-System Tools y Firmware

y Factory Defaults y Reboot

y Password y Log

Figure 5-30 System Tools menu

There are five submenus under the System Tools menu (shown in Figure 5-30):Firmware, Factory Defaults, Reboot, Password and Log. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below.

5.9.1 Firmware

The page (shown in Figure 5-31)allows you to upgrade to the latest version of firmware for the router.

37

Image 42
Contents Page COPYRIGHT & TRADEMARKS SAFETY NOTICES FCC STATEMENTEC DECLARATION OF CONFORMITY EUROPE COMMENT Appendix A Package contents TL-R402M Cable/DSL Router User Guide1.2 Conventions Chapter 1. About this Guide1.1 Purposes 1.3 Overview of this User Guide2.1 Overview of the Router 2.2 FeaturesChapter 2. Introduction TL-R402M Cable/DSL Router User GuideName 2.3 Panel LayoutTL-R402M Cable/DSL Router User Guide ActionTL-R402M Cable/DSL Router User Guide Figure 2-2Rear Panel sketch3.3 Connecting the Router Chapter 3. Connecting the Router3.2 Installation Environment Requirements 3.1 System RequirementsTL-R402M Cable/DSL Router User Guide Chapter 4. Quick Installation Guide 4.1 TCP/IP configurationTL-R402M Cable/DSL Router User Guide 4.2 Quick Installation Guide TL-R402M Cable/DSL Router User GuideFigure 4-4Login Windows TL-R402M Cable/DSL Router User GuideTL-R402M Cable/DSL Router User Guide Figure 4-6Choose WAN Connection TypeFigure 4-9Quick Setup - Finish TL-R402M Cable/DSL Router User Guide5.2 Status Chapter 5. Configuring the Router5.1 Login TL-R402M Cable/DSL Router User Guide5.4.1 LAN 5.3 Quick Setup5.4Network TL-R402M Cable/DSL Router User Guide5.4.2 WAN TL-R402M Cable/DSL Router User GuideTL-R402M Cable/DSL Router User Guide Figure 5-4WAN - Dynamic IPTL-R402M Cable/DSL Router User Guide Figure 5-5WAN - Static IP¾Connect on Demand - You can configure the router to disconnect your Internet connection after a specified period of inactivity Max Idle Time. If your Internet connection has been terminated due to inactivity, Connect on Demand enables the router to automatically re-establishyour connection as soon as you attempt to access the Internet again. If you wish to activate Connect on Demand, click the radio button. If you want your Internet connection to remain active at all times, enter 0 in the Max Idle Time field. Otherwise, enter the number of minutes you want to have elapsed before your Internet connection terminates TL-R402M Cable/DSL Router User GuideFigure 5-7PPPoE Advanced Settings TL-R402M Cable/DSL Router User GuideTL-R402M Cable/DSL Router User Guide Figure 5-8WAN - L2TP5.4.3 MAC Clone TL-R402M Cable/DSL Router User GuideDHCP yDHCP settings yDHCP Clients List 5.5DHCP5.5.1 DHCP Settings TL-R402M Cable/DSL Router User Guide5.5.2 DHCP Clients List 5.5.3 Address ReservationTL-R402M Cable/DSL Router User Guide TL-R402M Cable/DSL Router User Guide Figure 5-13Address ReservationTL-R402M Cable/DSL Router User Guide 5.6Forwarding5.6.1 Virtual Servers Forwarding yVirtual Servers yPort Triggering yDMZ5.6.2 Port Triggering TL-R402M Cable/DSL Router User GuideTL-R402M Cable/DSL Router User Guide Figure 5-16Port Triggering5.6.3 DMZ TL-R402M Cable/DSL Router User GuideTL-R402M Cable/DSL Router User Guide 5.7Security5.6.4 UPnP Security yFirewall yIP Filter yDomain Filter yMAC5.7.1 Firewall 5.7.2 IP Address FilteringTL-R402M Cable/DSL Router User Guide TL-R402M Cable/DSL Router User Guide Figure 5-21IP Address Filtering5.7.3 Domain Filtering TL-R402M Cable/DSL Router User GuideFor example TL-R402M Cable/DSL Router User Guide Figure 5-23Domain FilteringFor example 5.7.4 MAC Filtering TL-R402M Cable/DSL Router User Guide5.7.5 Remote Management TL-R402M Cable/DSL Router User GuideFox example TL-R402M Cable/DSL Router User Guide 5.8 Static Routing5.7.6 Ping from WAN To add static routing entriesTL-R402M Cable/DSL Router User Guide 5.9System Tools5.9.1 Firmware To modify an existing entry5.9.2 Factory Defaults TL-R402M Cable/DSL Router User Guide5.9.3 Reboot 5.9.4 PasswordTL-R402M Cable/DSL Router User Guide 5.9.5 Log TL-R402M Cable/DSL Router User GuideAppendix A FAQ TL-R402M Cable/DSL Router User GuideTL-R402M Cable/DSL Router User Guide 3.I want to use Netmeeting, what do I need to do?TL-R402M Cable/DSL Router User Guide Figure 5 DMZ2.Configure TCP/IP for your computer Appendix B Configuring the PCs1.Install TCP/IP component TL-R402M Cable/DSL Router User GuideTL-R402M Cable/DSL Router User Guide Assigned by DHCP SeverTL-R402M Cable/DSL Router User Guide Figure 13 DNS Configuration tabSetting IP address manually Figure 12 Gateway tabTL-R402M Cable/DSL Router User Guide Figure 14 IP Address tabFigure 16 DNS Configuration tab TL-R402M Cable/DSL Router User GuideCable/DSL Router User Guide Appendix C SpecificationsTL-R402M GeneralAppendix D Glossary TL-R402M Cable/DSL Router User GuideAppendix E Contact Information TL-R402M Cable/DSL Router User Guide