TP-Link TL-R480T+ manual Firmware, Load Balance Broadband Router User Guide

Page 81

1). Only one user can use these tools at one time.

TL-R480T+

Load Balance Broadband Router User Guide

¾Ping Size - Indicates the data field length of ping packet.

¾Ping Timeout - Indicates the time before the Ping timeout.

¾Tracert Hops – Specify the maximum hops of the Tracert here.

Click Start to start the test and the result will display in the Diagnostic Result table.

)Note:

1). Only one user can use these tools at one time.

2). These two functions may take several seconds sometimes, please wait.

3). Options "Number of Pings", "Ping size" and "Ping Timeout" are available for Ping function.

4). Option "Tracert Hops" is available for Tracert function.

4.13.3 Firmware

Choose menu “System Tools→Firmware”, you can update the latest version of firmware for the Router on the screen (shown in Figure 4-71).

Figure 4-71

¾Firmware Version - This displays the current firmware version.

¾Hardware Version - This displays the current hardware version. The hardware version of the upgrade file must accord with the Router’s current hardware version.

To upgrade the router's firmware, follow these instructions below:

Step 1: Download a more recent firmware upgrade file from the TP-LINK website (http://www.tp-link.com).

Step 2: Type the path and file name of the update file into the “File” field. Or click the Browse button to locate the update file.

Step 3: Click the Upgrade button.

)Note:

1)New firmware versions are posted at http://www.tp-link.comand can be downloaded for free. If the router is not experiencing difficulties, there is no need to download a more recent firmware version, unless the version has a new feature that you want to use.

2)When you upgrade the router's firmware, you may lose its current configurations, so please back up the router’s current settings before you upgrade its firmware.

3)Do not turn off the router or press the Reset button while the firmware is being upgraded.

4)The router will reboot after the upgrading has been finished.

75

Image 81

Contents Rev 4.1.0 TL-R480T+ Load Balance Broadband RouterAll rights reserved COPYRIGHT & TRADEMARKSCE Mark Warning FCC STATEMENTPackage Contents Conventionsor missing, please contact with your distributor Chapter 3. Quick Installation Guide Hardware installationChapter 1. Introduction ChapterAppendix C FAQ Appendix A SpecificationsAppendix B Preventing Lightning Appendix D GlossaryChapter 1.Introduction 1.2 Features1.1 Overview of the Router TL-R480T+1.3 Conventions 2.1 Panel Layout Chapter 2.Hardware installation2.1.1 The Front Panel StatusEnsure the router is powered on before it restarts completely 2.1.2 The Rear Panel2.2 System Requirements 2.3 Installation Environment Requirements2.4 Connect to Ground Connecting to the Grounding BarConnecting to the Ground via the power supply 2.5 Connecting the Router Load Balance Broadband Router User Guide 3.1 Configure PC Chapter 3.Quick Installation GuideLoad Balance Broadband Router User Guide Step 4 Configure the IP address as shown in Figure 3-4. After that, click OK 3.2 Login 2 Is the TCP/IP configuration for your PC correct?1 Is the connection between your PC and the Router correct? Step 1 Select the Quick Setup tab on the left of the main menu and the “Quick Setup” screen will appear. Click the Next button Step 3 If you choose PPPoE, you will see the screen as shown in Figure 3-10. Enter the Username and Password provided by your ISP. These fields are case sensitive. If you have difficulty with this process, please contact your ISP 4.1 Status Chapter 4.Configuring the Router¾ LAN - This field displays the current information for the LAN, including the “MAC address”, “IP address” and “Subnet Mask” 4.3 Network 4.2 Quick Setup4.3.1 WAN/LAN Number Please refer to chapter 3Quick Installation Guide1 By default, TL-R480T+ is set to work at the mode of dual WAN ports 4.3.2 LAN1. Dynamic IP 4.3.3 WAN¾ WAN Port Here allows you to select the WAN port to configure 2. Static IP 3. PPPoE ¾ Connect on Demand - You can configure the router to disconnect your Internet connection after a specified period of inactivity Max Idle Time. If your Internet connection has been terminated due to inactivity, Connect on Demand enables the router to automatically re-establish your connection as soon as you attempt to access the Internet again. If you wish to activate Connect on Demand, check the radio button and click Save to apply¾ Connect Automatically - Connect automatically after the router is disconnected. To use this option, click the radio button 4. BigPondCable ¾ Ingress Bandwidth Enter the bandwidth for download trafficLoad Balance Broadband Router User Guide 5. L2TP Load Balance Broadband Router User Guide 6. PPTP Load Balance Broadband Router User Guide 4.3.4 Network Service Detection 4.3.5 MAC Clone 4.3.6 Load Balance2 Only the PCs on your LAN can use the MAC Address Clone feature ¾ Enable/Disable WAN - Click the check box of WAN which you want to enable the Load Balance Bytes Tx + Rx - Bytes transmitted and received through the WAN port How to set an extra IP address dispatch rule? Step 3 Click Save to apply your setting 4.3.7 Balance PolicyTo add a dispatch rule Step 1 Click Add New… button, you will see the following screen4.3.8 WAN Port Parameter 4.4 DHCP 4.4.1 DHCP Settings 4.4.3 Address Reservation 4.4.2 DHCP Clients List2 The function wont take effect until the router reboots 4.5 ForwardingOther configurations for the entries as shown in Figure To add/modify a reserved IP addressTo add/modify a virtual server entry 4.5.1 Virtual Servers4.5.2 Port Triggering To add/modify a port triggering entry ¾ Trigger Port - This displays the port for outgoing traffic. An outgoing connection using this port will Trigger this rule4 Incoming Port Range cannot overlap each other 4.5.3 DMZTo assign a computer or server to be a DMZ server 4.5.4 UPnP4.5.5 ALG 4.6 Security4.6.1 Firewall 4.6.2 IP Filtering Step 6 Click the Save button to save this entry To add/modify an IP Address filtering entry4.6.3 Domain Filtering To add or modify a Domain Filtering entry To add or modify a MAC Filtering entry 4.6.4 MAC Filtering4.6.5 Screen ¾ Scan Attack Defence ¾ Region - This option used to select the specifically area from which the packets will be monitored by the next settingsIP address ten different ports, then the source IP address will be deemed to make Port Attacks. And the Router will start up the blocking function immediately ¾ DoS Attack Defence¾ Dubious Packet Defence ¾ Packet Defence with IP option 4.7 Static RoutingTo add/modify a static routing entry 4.8 Session Limit 4.8.1 Session LimitTo add/modify a session limit entry 4.9 QoS 4.8.2 Session ListYou can click the Refresh to update the information 4.9.2 QoS Rules List 4.9.1 QoS Settings4.10 IP & MAC Binding 4.10.1 Binding SettingSetting, ARP List To add/modify a QoS ruleTo add/modify an IP & MAC binding entry Step 2 Enter the MAC Address and IP Address in the corresponding fieldTo find a specific IP & MAC binding entry You can click “to page” to edit the entry in the corresponding screen 4.10.2 ARP List4.11.1 Dyndns DDNS 4.11 Dynamic DNSTo set up for Dyndns DDNS, follow these instructions 4.11.2 PeanutHull DDNSTo set up for PeanutHull DDNS, follow these instructions 4.11.3 Comexe DDNSTo set up for Comexe DDNS, follow these instructions 4.11.4 No-IP DDNSTo set up for No-IP DDNS, follow these instructions 4.12 Switch Settings4.12.2 Port Mirror 4.12.1 Port Statistics4.12.4 Port Parameter 4.12.3 Port Rate Control4.12.5 Port Status 4.12.6 Port VLAN 4.13 System Tools4.13.1 Time Settings To configure the system time manuallyTo configure the system automatically 2 The time will be lost if the router is turned off 4.13.2 Diagnostic ToolsTo upgrade the routers firmware, follow these instructions below 4.13.3 Firmware4 The router will reboot after the upgrading has been finished 1. Only one user can use these tools at one time4.13.5 Backup and Restore 4.13.4 Factory Defaults1 The default User Name is admin 2 The default Password is admin 3 The default IP Address is 4 The default Subnet Mask isTo restore the Router’s settings Step 2 Click the Restore button to completeStep 2 Save the file as the appointed file shown in Figure 4.13.7 Password 4.13.6 Reboot1 Change LAN IP Address. System will reboot automatically 2 MAC Clone system will reboot automatically 3 DHCP service function4.13.8 System Log 4.13.9 Remote Management3 You can click the Clean All button to clean all the configurations 4.13.10 Statistics MAC Address IP AddressTotal Packets4.13.11 IP NAT Table 4.13.12 NAT Source Port SettingsAppendix A Specifications GeneralPhysical and Environment Appendix B Preventing Lightning 1. How do I configure the router to access Internet by ADSL users? Appendix C FAQSave TL-R480T+ Load Balance Broadband Router User Guide3. I want to use Netmeeting, what do I need to do? Method one Use Virtual ServerFigure C-4 Method two Use DMZ Host7. I want to build a WEB Server on the LAN, what should I do? Figure C-7 Figure C-6Appendix D Glossary

Related manuals

Manual 131 pages 54.17 Kb