TP-Link manual TD-W8900GB54M Wireless ADSL2+ Router User Guide

Page 36

TD-W8900GB54M Wireless ADSL2+ Router User Guide

¾DHCP Server: These settings allow you to configure the Router‘s Dynamic Host Configuration Protocol (DHCP) server function. The DHCP server is enabled by default for the Router’s Ethernet LAN interface. DHCP service will supply IP settings to computers which are configured to automatically obtain IP settings that are connected to the Router though the Ethernet port. When the Router is set for DHCP, it becomes the default gateway for DHCP client connected to it. Keep in mind that if you change the IP address of the Router, you must change the range of IP addresses in the pool used for DHCP on the LAN.

„Start IP Address: Enter a value for the DHCP server to start with when issuing IP addresses. Because the default IP address for the Router is 192.168.1.1, the default Start IP Address is 192.168.1.2, and the Start IP Address must be 192.168.1.2 or greater, but smaller than 192.168.1.254.

„End IP Address: Enter a value for the DHCP server to end with when issuing IP addresses. The End IP Address must be smaller than 192.168.1.254. The default End IP Address is 192.168.1.254.

„Leased Time (hour): The Leased Time is the amount of time in which a network user will be allowed connection to the Router with their current dynamic IP address. Enter the amount of time, in hours, then the user will be “leased” this dynamic IP address. After the dynamic IP address has expired, the user will be automatically assigned a new dynamic IP address. The default is 24 hours.

¾Configure the second IP Address and Subnet Mask: You can configure the Router’s second IP Address and Subnet Mask for LAN Interface though which you can also access to the Web-based Utility as the default IP Address and Subnet Mask.

)Note:

UPnP, DHCP Server and the second IP Address are not available for the connection type of Bridge here, they won’t display on the screen above since only Bridge is selected.

¾Set Address Reservation: When you specify a reserved IP address for a PC on the LAN, that PC will always receive the same IP address each time when it accesses the DHCP server. Reserved IP addresses should be assigned to servers that require permanent IP settings.

To setup an Address Reservation entry:

1.Click the Set Address Reservation botton, and the Address Reservation screen pop up, as it showed below ;

2.Click New Entry botton to add new entries, and the screen showed below pop up, you can modify an address reservation entry in this screen;

29

Page 35 Page 37
Image 36
Page 35 Page 37
Contents TD-W8900GB 54M Wireless ADSL2+ Router Copyright & Trademarks FCC Statement FCC RF Radiation Exposure Statement54M Wireless ADSL2+ Router User Guide TD-W8900GBPackage contents Contents Wireless LAN Configuration AppendixPurpose ConventionsOverview of this User Guide Main Features WirelessOverview of the Router Supporting Protocol Transmit Data-rate Front Panel LED ExplanationName Status Indication ¾ Reset Button ¾ Wireless antennaBack Panel System RequirementsInstallation Environment Requirements Connecting the RouterBest Location for Wireless Network Connection Configure the Router Wired network connectionHub or Switch to Router Connection Connect Adsl LineTD-W8900GB54M Wireless ADSL2+ Router User Guide TD-W8900GB54M Wireless ADSL2+ Router User Guide TD-W8900GB54M Wireless ADSL2+ Router User Guide Configure PC TD-W8900GB54M Wireless ADSL2+ Router User Guide TD-W8900GB54M Wireless ADSL2+ Router User Guide TD-W8900GB54M Wireless ADSL2+ Router User Guide Basic Router Configuration Login Device InfoQuick Setup Advanced Setup1 WAN Follow the instructions below to Add or Edit an ATM PVC TD-W8900GB54M Wireless ADSL2+ Router User Guide TD-W8900GB54M Wireless ADSL2+ Router User Guide PPPoA TD-W8900GB54M Wireless ADSL2+ Router User Guide PPPoE MERTD-W8900GB54M Wireless ADSL2+ Router User Guide IPoA BridgeTD-W8900GB54M Wireless ADSL2+ Router User Guide 2 LAN TD-W8900GB54M Wireless ADSL2+ Router User Guide 3 NAT Virtual Servers To setup a virtual server entry TD-W8900GB54M Wireless ADSL2+ Router User Guide Port Triggering To add a new Port TriggeringDMZ Host Security To add a new DMZ HostALG Setup an Outgoing IP Filtering rule IP FilteringTD-W8900GB54M Wireless ADSL2+ Router User Guide Setup an Incoming IP Filtering rule To setup a MAC Filtering rule MAC FilteringParental Control Quality of Service To setup a Parental Control ruleTD-W8900GB54M Wireless ADSL2+ Router User Guide Routing Default Gateway Static Route To add static routing entriesTo remove a static routing entry RIP7 DNS DNS ServerTo setup DDNS, follow these instructions Dynamic DNS8 DSL Port Mapping TD-W8900GB54M Wireless ADSL2+ Router User Guide TD-W8900GB54M Wireless ADSL2+ Router User Guide Wireless LAN Configuration Wireless BasicWireless Security WEP EncryptionConfigure WEP Encryption WPA Configure WPA settings Configure WPA-PSK settings WPA-PSKWPA2 WPA2-PSK Mixed WPA2/WPAWireless -- MAC Filter Mixed WPA2/WPA-PSKWireless Advanced Form of MAC Address must be xxxxxxxxxxxx, like 00130A55FF09TD-W8900GB54M Wireless ADSL2+ Router User Guide Diagnostics Wireless StatisticsSettings BackupTo back up the Router’s current settings ManagementUpdate To update the Router’s settings System LogTo Configure the System Log Settings To View the System LogInternet Time 4 TR-069 client To set the Router’s timeRPC- Remote Procedure Calls Access Control ServicesPasswords To add the IP AddressUpdate Software To change the passwordReboot To update the Routers softwareAppendix Appendix a GlossaryTD-W8900GB54M Wireless ADSL2+ Router User Guide TD-W8900GB54M Wireless ADSL2+ Router User Guide TD-W8900GB54M Wireless ADSL2+ Router User Guide Appendix BSpecifications LED LAN/WAN
Top Page Image Contents