ZyXEL Communications 240B manual Configuring a Filter Rule, 2 TCP/IP Filter Rule

Page 57

 

 

 

ExpWave 240B Secure Outdoor Ethernet Radio Link

 

 

 

 

 

 

 

 

[N] means there are no more rules to check.

 

m

Refers to Action Matched.

[F] means to forward the packet.

 

 

 

 

[D] means to drop the packet.

 

 

 

 

[N] means check the next rule.

 

 

n

Refers to Action Not Matched

[F] means to forward the packet.

 

 

 

 

[D] means to drop the packet.

 

 

 

 

[N] means check the next rule.

 

The protocol dependent filter rules abbreviation are listed as follows:

If the filter type is IP, the following abbreviations listed in the following table will be used.

Table 9-2 Abbreviations Used If Filter Type Is IP

Abbreviation

Description

 

 

Pr

Protocol

 

 

SA

Source Address

 

 

SP

Source Port number

 

 

DA

Destination Address

 

 

DP

Destination Port number

 

 

If the filter type is GEN (generic), the following abbreviations listed in the following table will be used.

Table 9-3Abbreviations Used If Filter Type Is GEN

Abbreviation

Description

 

 

Off

Offset

 

 

Len

Length

 

 

Refer to the next section for information on configuring the filter rules.

9.3.1 Configuring a Filter Rule

To configure a filter rule, type its number in Menu 21.1 - Filter Rules Summary and press [ENTER] to open Menu

21.1.1for the rule.

To speed up filtering, all rules in a filter set must be of the same class, i.e., protocol filters or generic filters. The class of a filter set is determined by the first rule that you create. When applying the filter sets to a port, separate menu fields are provided for protocol and device filter sets. If you include a protocol filter set in a device filter field or vice versa, the ExpWave will warn you and will not allow you to save.

9.3.2 TCP/IP Filter Rule

This section shows you how to configure a TCP/IP filter rule. TCP/IP rules allow you to base the rule on the fields in the IP and the upper layer protocol, e.g., UDP and TCP, headers.

To configure a TCP/IP rules, select TCP/IP Filter Rule from the Filter Type field and press Enter to open Menu 21.1.1 - TCP/IP Filter Rule, as shown below.

Filter Setup

9-3

Image 57
Contents ExpWave 240B Page Disclaimer TrademarksCopyright FCC Statement Information for Canadian Users Information for Canadian UsersCanadian Users Product installation requirementsWarranty Vii ZyXEL Limited WarrantyCustomer Support Customer SupportTable of Contents 11-1 10-112-1 Firmware and Configuration File13-1 14-115-1 IP Routing Policy SetupList of Figures/Tables 17 Physical Installation of ExpWave with flat panel antennaMenu 24.2 System Information and Console Port Speed Abbreviations Used in the Filter Rules Summary Menu List of TablesPage Non-physical Features of the ExpWave 240B Physical Features of the ExpWave 240BGetting to Know Your ExpWave Introduction to the ExpWave 240BIP Policy Routing Benefits of the ExpWave 240BSpecifications of the ExpWave 240B Specification of ExpWave 240BApplications of the ExpWave 240B Security Installation Page Connectors of bottom Hardware InstallationHardware Installation Hardware DescriptionAntena connector of the top Male RF connector with Connecting to the outdoor antennaAntenna Option RF cable Front view of flat panel antenna10 Grounding wire Mounting bracket Grounding wireExpWave 240B Physical Connection 14 Ethernet Cable Switching Power AdapterInstallation Procedure Install the outdoor unit with the flat panel antenna Install the outdoor unit with the omni-directional antennaHardware Installation Operation Mode Instruction of ExpWave Initial SetupInitial Setup Network Topology PlanningBridge Mode Menu Wireless Setup Router Mode 11 TCP/IP and Dhcp Ethernet Setup Turning On ExpWave 14 AC1 LAN Dhcp SetupMain Menu Commands Entering the PasswordInitial Screen Navigating the SMT InterfaceMain Menu Routing AP Summaries of SMT MenuMain Menu Summary 20 Menu 23 System Password Changing the System PasswordPage General Setup Menu 1 General SetupGeneral Setup System NameGeneral Setup LAN Port Filter Setup LAN SetupWireless Setup IntroductionFactory LAN Defaults Dhcp ConfigurationIP Address and Subnet Mask RIP Setup LAN Setup MenuPrivate IP Address Ranges Dhcp Ethernet Setup Menu Fields Menu 3 LAN Dhcp SetupBoth LAN TCP/IP Setup Menu FieldsOptions are Both , In Only , Out Only or None RIP-1Page Wireless Setup DisableBit WEP 1/2/3/4 Network Setup Field Network SetupNetwork Setup Set AC Enable or DisableSMT 6.1 Menu in Router Mode VPN security levelServer Static Route Setup IP Static Route SetupStatic Route Setup IP Static Route Menu Fields Menu 12 Edit IP Static RouteThis chapter shows you how to create and apply filters Filter Setup ConfigurationFilter Setup About FilteringConfiguring a Filter Set Filter Rules Summary MenuAbbreviations Description Display 2 TCP/IP Filter Rule Configuring a Filter RuleAbbreviations Used If Filter Type Is IP 3Abbreviations Used If Filter Type Is GENTCP/IP Filter Rule Menu Fields Next diagram illustrates the logic flow of an IP filter Generic Filter Rule Menu Fields Generic Filter RuleApplying a Filter and Factory Defaults Ethernet trafficCheck Next Matched Rule Forward Drop Page Snmp Configuration Snmp Configuration 10-1About Snmp Snmp Configuration Menu Fields Snmp ConfigurationSupported MIBs Snmp TrapsRFC-1215 Snmp Configuration 10-3Page System Maintenance 11-1 System MaintenanceSystem Status This chapter covers SMT menus 24.1 toSystem Maintenance System Maintenance Status Menu FieldsSystem Information and Console Port Speed System InformationConsole Port Speed System Maintenance 11-3Viewing Error Log Log and TraceUnix Syslog Diagnostic System Maintenance Menu Syslog ParametersSystem Maintenance 11-5 WAN Dhcp System Maintenance Menu DiagnosticSystem Maintenance 11-7 Page Firmware & Configuration File Maintenance 12-1 Backup ConfigurationFilename Conventions Filename ConventionsExample of FTP Commands from the Command Line Using the FTP Command from the Command LineGeneral Commands for GUI-based FTP Clients Firmware & Configuration File MaintenanceTftp Command Example Backup Configuration Using TftpGeneral Commands for GUI-based Tftp Clients Firmware & Configuration File Maintenance 12-3System Maintenance Backup Configuration Backup Via Console PortRestore Using FTP Restore ConfigurationRestore Using FTP Session Example Firmware & Configuration File Maintenance 12-5Restore Via Console Port Uploading Firmware and Configuration FilesFirmware File Upload Configuration File Upload FTP File Upload Command from the DOS Prompt ExampleFirmware & Configuration File Maintenance 12-7 Tftp Upload Command Example FTP Session Example of Firmware File UploadTftp File Upload Firmware & Configuration File Maintenance 12-9 Example Xmodem Firmware Upload Using HyperTerminalUploading Via Console Port Uploading Firmware File Via Console PortExample Xmodem Configuration Upload Using HyperTerminal Uploading Configuration File Via Console PortCommand Interpreter Mode System Maintenance InformationTime and Date Setting Firmware & Configuration File Maintenance 13-1NTP RFC-1305 the default, is similar to Time RFC-868 Firmware & Configuration File Maintenance 13-3 Resetting the TimePage Telnet Remote Management14.2 FTP SnmpRemote Management Limitations Remote ManagementLAN Only IP Routing Policy Setup IP Routing Policy SetupBenefits Routing PolicyCriterion IP Policy RoutingService Delay , Max Thruput or Max ReliableIP Policy Routing 15-3 Ethernet IP Policies Applying an IP PolicyLess , Greater , Less or Equal or Greater or Equal Reliable or Min CostIP Policy Routing 15-5 IP Policy Routing Example15-6

240B specifications

ZyXEL Communications has long been a prominent player in the networking equipment industry, and the ZyXEL 240B modem exemplifies the company's commitment to delivering reliable and efficient solutions for both home and business users. The ZyXEL 240B is a high-performance DSL modem designed to provide stable internet connectivity while supporting advanced telecommunications technologies.

One of the standout features of the ZyXEL 240B is its compliance with the latest ADSL2+ and VDSL2 standards, ensuring that users can take advantage of high-speed internet connections. With download speeds reaching up to 100 Mbps and upload speeds of 50 Mbps, the 240B is well-suited for streaming, online gaming, and other bandwidth-intensive activities.

The modem comes equipped with a robust Wi-Fi module that supports dual-band connectivity, allowing devices to connect securely over both the 2.4 GHz and 5 GHz frequency bands. This dual-band feature enhances the overall network performance by reducing interference and improving data throughput for multiple devices operating simultaneously. Moreover, the ZyXEL 240B supports the latest Wi-Fi standards, including 802.11ac, ensuring compatibility with a vast range of Wi-Fi-enabled devices.

Security is a top priority for ZyXEL, and the 240B is equipped with advanced encryption protocols such as WPA3, ensuring that users' data remains protected from unauthorized access. The modem also features integrated firewall capabilities, providing an additional layer of security against potential cyber threats and intrusions.

The ZyXEL 240B is designed for easy setup and management. With a user-friendly web interface, users can quickly configure their network settings, monitor connected devices, and troubleshoot potential connectivity issues. Additionally, the modem supports TR-069, allowing service providers to remotely manage and maintain the device, significantly enhancing user experience.

In terms of hardware characteristics, the ZyXEL 240B boasts multiple Ethernet ports, enabling users to connect wired devices for a more stable internet connection. The modem's compact design also makes it an ideal addition to any home or office environment without taking up excessive space.

Overall, the ZyXEL 240B modem is a reliable choice for anyone in need of a high-speed internet solution, offering robust features, enhanced security, and seamless connectivity for all digital needs.