Peavey PV Series Front Panel Features, Power Leds PWR, Signal Activity Leds SIG, DDT Active Leds

Page 5

FRONT PANEL FEATURES

1

2 3 4

4 3 2

1

5

(1)INPUT GAIN (dB)

These controls are used to adjust the input gain of each channel. They determine how “loud” each channel of the power amplifier will sound for a given input signal level. Maximum input gain is achieved at the fully clockwise setting (+32 dB, 40 X), and this setting yields maximum mixer/system headroom. A setting of less than fully clockwise will yield lower system noise at the expense of mixer/system headroom. Turning the control fully counterclockwise is the “off” setting (-∞). It is always a good idea to power up any new installation at this setting to protect the system loudspeakers.

(2)POWER LEDS (PWR)

These indicators illuminate when the AC mains power is being supplied to the amp and both channels are operational. If either channel experiences fault conditions, exceeds safe operating temperature limits, or if the mains circuit breaker trips; both channel power LEDs will be dark, indicating “shutdown”. If the BRIDGE mode is selected, the PWR indicator on channel B will remain dark as a positive indication of this mode selection.

(3)SIGNAL ACTIVITY LEDS (SIG)

These indicators illuminate when the associated channel output signal level exceeds 1 V RMS.

(4)DDT™ ACTIVE LEDS

These indicators illuminate when DDT compression is taking place in the associated channel. With the DDT ENABLE / DEFEAT switch on the back panel in the ENABLE position, these LEDs indicate clipping is occurring in the corresponding channel. The Peavey DDT compression system will be covered in greater detail later in this manual.

(5)POWER SWITCH

This heavy-duty, rocker-type switch turns on the mains power to the amplifier. When the mains power is applied, there is a three-second delay in activation of the unit. This reduces/eliminates the turn-on transients associated with the system equipment connected to the amplifier and protects loudspeakers.

(6)CIRCUIT BREAKER

There is one circuit BREAKER on the PV® amplifier. This breaker is provided to limit current to the associated power transformer, and protect it from overheating and possible destruction due to fault conditions in the unit. The trip current values have been carefully chosen to allow reasonable continuous power output performance, while still protecting the power transformer. This breaker should not trip unless there is a fault in the amplifier circuitry that causes excessive mains current draw. However, abnormal conditions such as a short circuit on either or both channels, or continuous operation at overload or clipping (especially into 2-Ohm loads per channel or 4-Ohm bridge load) can cause the breaker to trip. If this occurs, turn the POWER switch OFF and reset the breaker, after waiting a brief period of time to allow the unit to cool down. Efforts should be made to correct the cause of the overload if possible. When tripped, the button on the BREAKER will be outward approximately 1/4" and can be reset by pushing inward and upward. A normal reset button is relatively flat. If the breaker trips instantly each time you attempt to turn the unit on, it should be taken to a qualified Peavey Service Center for repair.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents S E R I E S a M P S Page Important Safety Instructions Installation PV Series Professional Stereo Power AmplifierBasic Setup IntroductionPower Leds PWR Front Panel FeaturesSignal Activity Leds SIG Power SwitchBinding Post Outputs Back Panel Features IEC Mains ConnectorDomestic AC Mains Cord DDT Distortion Detection Technique Switch Mode SwitchCombo Input Connector Speakon OutputsCrossover Switch 150 Hz Xover LOW CUT SwitchIndustrial and Commercial Installations THRU/LOW OUT JacksDDT Bridge ModeAmplifier Configurations Stereo BI-AMPED System Input Sensitivity & Impedance SpecificationsMise EN Route Rapide Amplificateurs Proffessionnels Stereo PV SeriesIDEBALLAGE Panneau Avant Leds DE Signal SIGLeds D’ALIMENTATIONPWR Leds DDTPanneau Arriere Connecteur IEC Selecteur DE ModeNe jamais déconnecter la connexion de terre de votre unité BornierOuverture DE Ventilation Selecteur DDT Distortion Detection TechniqueBloc DE Connexions D’ENTREES Entree ComboSorties Jacks High OUT Installations Industrielles ET CommercialesSorties Jacks THRU/LOW Mode Pont Bridge Stereo mode, below rated output power, 4 ohms Introducción Serie DE Amplificadores Profesionales Estéreo PVDesempaque InstalaciónBraker Funciones DEL Panel FrontalInterruptor DE Corriente Funciones DEL Panel Trasero Parrilla DEL Ventilador Interruptor DDT Técnica DE Detección DE DistorsiónBarrera DE Entradas Conectador DE Entrada ComboSalida DE GRAVES/ a Través Modo Puente Page Peavey Electronics Corporation Limited Warranty 2001

PV Series specifications

Peavey is a well-known name in the music industry, particularly recognized for its range of audio equipment. Within its extensive portfolio, the PV Series stands out as a line of amplifiers and speakers that have earned a reputation for delivering high-quality sound performance and robust build quality. The PV Series is designed to cater to a variety of audio needs, making it an essential choice for musicians, sound engineers, and event organizers alike.

One of the main features of the PV Series is its impressive power handling capacity. The PV amplifiers are built to deliver high wattage output, ensuring that even in large venues, audio enthusiasts receive clear and powerful sound. This capability is complemented by the series' advanced speaker design, which includes high-efficiency drivers and reinforced construction. Whether for live performances, studio applications, or installation in permanent venues, the PV Series maintains clarity and fidelity at both low and high volumes.

Another defining characteristic of the PV Series is its versatility. The range includes powered and passive speakers designed to cater to a wide spectrum of sound reinforcement needs. The powered speakers offer built-in amplifiers, eliminating the need for external power sources, which simplifies setup and transportation. On the other hand, the passive speakers can be paired with various amplifiers to suit specific performance requirements.

Peavey’s unique technologies are also pivotal to the PV Series’ acclaim. The series benefits from proprietary innovations such as the DDT (Dynamic Drive Limiting) technology, which helps prevent distortion by monitoring signal levels in real-time. This ensures that users can push their equipment to the limit without risking damage to their speakers, providing peace of mind during critical performances.

Durability is a hallmark of the PV Series. The enclosures are made from high-quality materials designed to withstand the rigors of travel and use. Features such as reinforced corners, heavy-duty grills, and weather-resistant finishes make these products suitable for both indoor and outdoor use.

Finally, the PV Series offers an appealing price-to-performance ratio, making high-quality audio accessible to a wider range of users. Whether one is a seasoned professional or a budding enthusiast, the Peavey PV Series provides reliable and powerful audio solutions that stand the test of time. With a combination of power, versatility, and durability, it continues to be a preferred choice in various audio environments.
Top Page Image Contents