ZyXEL Communications AG-200 manual FCC Statement

Page 4

ZyXEL AG-200 User’s Guide

Federal Communications Commission (FCC) Interference Statement1

The device complies with Part 15 of FCC rules. Operation is subject to the following two conditions:

This device may not cause harmful interference.

This device must accept any interference received, including interference that may cause undesired operations.

This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

If this equipment does cause harmful interference to radio/television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1.Reorient or relocate the receiving antenna.

2.Increase the separation between the equipment and the receiver.

3.Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

4.Consult the dealer or an experienced radio/TV technician for help.

Notice 1

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Caution

This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

1Refer to the Quick Start Guide for model specific FCC statement.

iv

FCC Statement

Image 4
Contents ZyXEL AG-200 Disclaimer Copyright 2004 by ZyXEL Communications CorporationTrademarks ZyXEL Limited Warranty Online RegistrationFCC Statement Customer Support Table of Contents ZyXEL AG-200 User’s Guide About This Users Guide Syntax ConventionsRelated Documentation User Guide FeedbackGraphics Icons Key Page Using the ZyXEL Utility to Configure Your Network ZyXEL AG-200 Hardware and Utility InstallationAbout Your ZyXEL AG-200 ZyXEL AG-200 User’s Guide Network Profile AddZyXEL AG-200 User’s Guide ZyXEL AG-200 User’s Guide ZyXEL AG-200 User’s Guide Apply RemoveProperties Each page in Properties is explained below ZyXEL AG-200 User’s Guide ZyXEL AG-200 User’s Guide Security Mode ZyXEL AG-200 User’s Guide ZyXEL AG-200 User’s Guide ZyXEL AG-200 User’s Guide Refresh Site SurveyStrong Scan Detail Info Connect Add to profileOptions Launch at windows startupAuto Dhcp renewal Auto-Profile SelectionZyXEL AG-200 User’s Guide Getting Started Version Page Wireless Network Application OverviewSsid ChannelAd-Hoc Ibss BSS ExampleRoaming Infrastructure Network ExampleWireless LAN Security Roaming ExampleEAP Authentication Data Encryption with WEPIeee 3 WPAWPA-PSK Application Example User AuthenticationEncryption WPA-PSK Authentication WPA with Radius Application ExampleFragmentation Threshold RTS/CTS ThresholdAuthentication Type RTS ThresholdZyXEL AG-200 User’s Guide Chapter Maintenance Version ScreenUninstalling the ZyXEL Utility AboutUpgrading the ZyXEL Utility Page Configuring Security Configuring WEPZyXEL AG-200 User’s Guide Configuring WPA-PSK Configuring Configuring WPAConfiguring 802.1x EAP-MD5 Configuring 802.1x EAP-LEAP Configuring 802.1x EAP-PEAPZyXEL AG-200 User’s Guide Configuring 802.1x EAP-TLS ZyXEL AG-200 User’s Guide Configuring 802.1x EAP-TTLS ZyXEL AG-200 User’s Guide Problems Starting the ZyXEL Utility Program Problem with the Link StatusTroubleshooting Starting ZyXEL Utility Program Troubleshooting Link QualityProblems Communicating With Other Computers Troubleshooting Communication ProblemsEAP-TTLS Tunneled Transport Layer Service EAP-MD5 Message-Digest AlgorithmEAP-TLS Transport Layer Security Peap Protected EAPComparison of EAP Authentication Types Leap
Related manuals
Manual 2 pages 60.26 Kb