Peavey Classic 30 manual Power Amplifier Section, Preamp Section

Page 11

Classic® 30

All-Tube Guitar Amplifier

SPECIFICATIONS

POWER AMPLIFIER SECTION

Four 6BQ5/EL84s with 12AX7 driver

Rated Power & Load:

30 W RMS into 16 or 8 ohms

Power @ Clipping (Typically):

(5% THD, 1 kHz, 120 VAC line)

3O W RMS into l6 or 8 ohms

(Bias must be reduced to measure.)

Frequency Response:

+0, -2 dB, 50 Hz to 15 kHz, @ 20 W RMS into 16 ohms

Hum & Noise:

No greater than 80 dB below rated power

Power Consumption:

150 watts, 50/60 Hz, 120 VAC (Domestic)

PREAMP SECTION

Two 12AX7’s

The following specs are measured @ 1 kHz with the controls preset as follows:

Pre & Post (lead) @ 0 Reverb Level @ 0 Bass & Treble EQ @ 12 Middle EQ @ 0 Channel Select Out Boost Switch Out

Nominal level is with Input Gain @ 6 Minimum level is with Input Gain @ 12

Preamp Normal Input:

Impedance: Very high Z, 470 K ohms

Lead Channel (Post Gain @ 12):

Nominal Input Level: -40 dBV, 10 mV RMS Minimum Input Level: -70 dBV, 0.3 mV RMS

Normal Channel (Post Gain @ 12):

Nominal Input Level: -17 dBV, 140 mV RMS Minimum Input Level: -28 dBV, 40 mV RMS Maximum Input Level: 0 dBV, 1.0 V RMS

Equalization:

(Lead and Normal Channels)

Custom bass, middle, and treble passive-type EQ

Effects Send:

Load Impedance: 1 K ohm or greater

Nominal Output Level: -6 dBV, 0.5 V RMS

Effects Return:

Impedance: High Z, 2 M ohms

Designed Input Level: -6 dBV, 0.5 V RMS (Switching jack provides Effects Send to Effects Return connection when not used.)

External Footswitch Function:

Reverb Defeat (when reverb control is raised) Normal/Lead Channel Select (when Lead activated)

Speaker (Combo Only):

One 12" Blue Marvel 16 ohms

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Classic Page Important Safety Instructions Bewahren SIE Diese Sicherheitshinweise AUF Gardez CES Instructions Guarde Estas Instrucciones All-Tube Guitar Amplifier FeaturesEffects Return Power SwitchBoost Switch Pilot Light LEDInput Channel Select SwitchNormal Gain Line Cord 120 V Products only Remote Switch JackExternal Speaker Jack Preamp Section Power Amplifier SectionMerkmale Gitarren-VollröhrenverstärkerWarnung Regelt den Pegel des Normal Kanals Netzkabel nur bei 120 V-Geräten C K S E I T EVorverstärkerstufe EndstufeCaracteristiques Amplificateur guitare tout lampeRetour d’effets Boost SwitchInterrupteur d’alimentation DEL témoinEntrée Sélecteur de canalGain canal Normal Cordon Secteur Modèles en 120 V uniquement External Speaker JackPrise pour interrupteur à distance Section Preamplification Section AmplificationCaracterísticas Amplificador a válvulas para guitarraEnvío de efectos Interruptor de corrienteLED indicador de lámpara Retorno de efectosEntrada Interruptor de selección de canalGanancia normal Cable DE Linea modelos de 120 V únicamente Enchufe hembra de interruptor remotoSección DE Previo Sección DE LA Etapa DE PotenciaProduct Category Peavey Electronics Corporation Limited Warranty80305324

Classic 30 specifications

The Peavey Classic 30 is a highly regarded tube guitar amplifier that has earned a reputation for its exceptional tone, versatility, and roadworthy design. First introduced in the mid-1990s, this amplifier has remained a favorite among musicians due to its impressive sound characteristics and robust construction.

One of the standout features of the Classic 30 is its all-tube design. Equipped with four EL84 power tubes and three 12AX7 preamp tubes, this amplifier delivers a warm, dynamic sound that is rich in harmonics. The 30-watt output provides ample power for both practice sessions and live performances, making it suitable for various musical genres including rock, blues, country, and jazz.

The Classic 30 features a single 12-inch speaker, usually a Peavey Blue Marvel, which contributes to its punchy, resonant tone. This speaker choice enhances the amplifier’s clarity and definition, making it an excellent platform for both clean and overdriven sounds. The amp also boasts a standard four-input design, allowing guitarists to experiment with different tonal options by mixing bright and normal channels.

Another key characteristic of the Peavey Classic 30 is its innovative Tone Controls. Featuring bass, mid, treble, and a presence control, the amp allows users to sculpt their sound precisely to their liking. The reverb feature adds additional depth to the mix, providing a subtle ambiance that enhances the overall tonal quality.

In terms of build quality, the Classic 30 is designed to withstand the rigors of touring musicians. The sturdy construction ensures longevity while maintaining a lightweight profile, which is vital for artists on the road. The combo design also makes it easy to transport, yet it delivers a powerful sound that fills a room.

Moreover, the Classic 30 includes a footswitchable lead channel, which enables players to easily switch between clean and overdriven tones. This dynamic range is particularly appealing for performers who rely on quick changes during a set.

With its combination of classic tube tone, versatile features, and solid build, the Peavey Classic 30 stands out as an iconic amplifier that meets the needs of guitarists at all levels. Whether in the studio or on stage, this amp provides a reliable and inspiring tool for any musician's arsenal.
Top Page Image Contents