Linksys PPS1UW manual Windows Driver Setup, At this point, you must have

Page 7

Instant EtherFast® Series

Chapter 4: Windows Driver Setup

Overview

This section installs the PrintServer’s software on your Windows 95, 98, Millennium, NT, 2000, or XP computers to give them PrintServer printing abil- ities. The PrintServer is fully compatible with Windows 95, 98, Millennium, NT 4.0, 2000, and XP environments.

At this point, you must have:

the PrintServer hardware installed on your network. If not, see Chapter 3: Hardware Installation.

TCP/IP installed on each of your computers.

an IP address assigned to each of the computers on your network. If not, see Chapter 9: DHCP Support for the Wireless-Ready PrintServer.

an IP address assigned to the PrintServer. By default the PrintServer has DHCP enabled. If you need to assign an IP address, go to Chapter 5: Bi- Admin: PrintServer Management.

This setup should be completed on the network administrator’s computer before all other users’ computers on the network. The PrintServer’s IP address will be assigned in this first installation on the network administrator’s com- puter only, which takes three extra steps.

It is assumed that your CD-ROM drive’s letter name is designated as “D”. If your CD drive is named another letter, replace all instances of “D” with the appropriate letter.

If you need to install the PrintServer’s driver on computers without a CD-ROM drive, you can create a setup disk by using a computer with a CD-ROM drive to copy the contents of D:\Driver\Win9xNT onto a floppy disk.

EtherFast® Wireless-Ready USB PrintServer

The Autorun Bi-Admin Management Utility Installation

1.Insert the Setup Utility CD. A built-in autorun will begin the installation of the PrintServer’s Bi-Admin Management Utility, and display Figure 4-1. Click the product you wish to install, followed by the Install tab to continue.

Figure 4-1

2.The installation routine will begin to run and display Figure 4-2. Close any other programs you might have running during this installation procedure, and click the Next button to continue or Cancel to forgo installation.

Figure 4-2

7

8

Image 7
Contents EtherFast Wireless- Ready USB PrintServer Copyright & Trademarks Table of Contents Introduction Instant EtherFast Wireless-Ready USB PrintServerFeatures Package ContentsWireless-Ready USB PrintServer’s Ports Wireless-Ready USB PrintServer’s LEDsFinding the Wireless-Ready USB PrintServer’s Default Name Hardware InstallationOverview Autorun Bi-Admin Management Utility Installation Windows Driver SetupAt this point, you must have Installing the Wireless-Ready USB PrintServer’s Drivers Instant EtherFast Series Instant EtherFast Series Starting the Bi-Admin Management Utility Bi-Admin PrintServer ManagementUsing Bi-Admin Bi-Admin Help FilesRefreshing the Device List Refresh Icon Setting the Wireless-Ready USB PrintServer’s IP AddressChanging the Device Name Attaching Bi-Admin to a Remote Linksys PrintServerResetting the Wireless-Ready USB PrintServer Restoring Factory DefaultServer Accessing the Web-Based UtilityWhen the Configure Server screen appears Open your web browsTCP/IP WirelessStatus Advanced PropertiesAppleTalk Mail Server IP Address is Internet PrintingLogical Printers Snmp NetBEUIInternet Printing Protocol IPP Windows IPP Client SetupChanging the IPP Port Settings Installation is now completeIPP Client Setup for Windows 2000 and XP Open the Printers folder Start = Settings = PrintersIPP printer is now ready for use Using IPP Printers Appendix B About Bi-Directional Printing Appendix a TroubleshootingHardware Issues General Printing IssuesAppendix D Glossary Instant EtherFast Series Instant EtherFast Series Instant EtherFast Series LAN Appendix E SpecificationsAppendix F Environmental Appendix G Warranty InformationWeb FTP Site Technical Support RMA Issues FaxAppendix H Contact Information Sales InformationCopyright 2002 Linksys, All Rights Reserved