Fujitsu 2300 manual Power icon is blinking Suspend-to-RAMmode

Page 26

The Power icon either flashes or is not displayed when system operation is suspended, depending on how your system is configured. At this point, programs that were running are stopped, active data is saved, and the system enters one of two different low-power states, or suspend modes, as explained in the following paragraphs.

2.Observe the Power icon in the Status display to determine which suspend mode your system is using.

•Power icon is blinking: Suspend-to-RAMmode

In this mode, active data is saved by maintaining power to RAM while most other system components are powered off. The Battery Gauge icon in the Status display indicates the battery charge level. A fully charged battery pack can maintain data in RAM for approximately 10 days; a partially charged battery pack will maintain data in RAM for proportionately less time.

•Power icon is not displayed: Suspend-to-Diskmode

In this mode, active data is stored on the hard disk drive and power usage is reduced to the same level used in the Off state. When the system is in Suspend-to-Diskmode, the Battery Gauge icon is not visible in the Status display. In this mode, there is no danger of losing data if battery power is lost. A fully charged battery pack will discharge to the critically low level after about 45 days in the Off state.

If you have successfully performed this procedure, system operation is now suspended. Refer to “Resuming System Operation” later in this chapter to resume system operation. Also, note the following with regard to suspending system operation:

•You can remove the battery pack while the system is in Suspend-to-RAM or Suspend-to-Disk modes in order to install a charged battery pack. To prevent losing unsaved data, wait until system operation is suspended before you remove the battery pack.

•Your system may be configured to suspend operation automatically after a period of inactivity.

•Your system may be configured to enter Suspend-to-Disk mode automatically after a period of time in Suspend-to-RAM mode.

•The system uses a small amount of battery power when in Suspend-to-RAM mode. Eventually, the battery will become fully discharged.

Note: If you will not be using the system for an extended period of time, shut down the system rather than using Suspend-to-RAM mode.

Suspending System Operation

2-5

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Page Page Page Copyright Fujitsu Personal Systems, Inc Page Agency Compliance UL NoticesTelephone FCC NoticesAddress Table of Contents Appendix a Agency Notices Getting Started Included with the Stylistic 2300 Pen TabletOptional Accessories Stylistic 2300 Pen Tablet Features Front FeaturesStylistic 2300 Pen Tablet Features Front View Stylistic 2300 Pen Tablet Features Rear View Status Display System Status IndicationsStatus Display Connectors and Peripheral Interfaces Peripheral ConnectorsFDD Connector Connector Pen Tablet Icon Purpose Connector Pen Tablet Icon Purpose Peripheral Getting Started Using the Stylistic 2300 Pen Tablet System StatesOff state Changing System StatesStarting the Pen Tablet Shutting Down the System Suspending System OperationPower icon is blinking Suspend-to-RAMmode Power icon is not displayed Suspend-to-DiskmodeResuming System Operation Programmable hotpad Using HotpadsVolume hotpads Speaker Mute hotpadContrast hotpads Using the PenDisplay Select hotpad Brightness hotpadsStylistic 2300 Pen Charging the Battery Pack Battery Pack Charging TimeRemoving and Installing the Battery Pack Conserving Battery Power Removing and Installing the Battery PackCare of Bridge Battery Modem ConnectionPC Card Slots PC Card SlotsCare and Maintenance Protecting the Display ScreenStoring the Stylistic 2300 Pen Tablet Cleaning the Display Screen Avoiding OverheatingReplacing the Pen Tip Replacing the Pen TipReplacing the Pen Battery Opening the PenCalibrating the Pen Calibrating the Pen Solving Problems System Will Not Resume OperationInfrared Data Transfer Is Not Working Configuring Peripherals Interfaces Agency Notices 2Appendix DOC Industry Canada Compliance Notices Avis Aux Utilisateurs Du Réseau Téléphonique Canadien Avertissement 6Appendix Index Index-1Index-2 Index-3 Index-4

2300 specifications

The Fujitsu 2300 is a versatile and powerful computing solution that has gained recognition in various industries for its robust performance and rich feature set. Designed for enterprise environments, the Fujitsu 2300 stands out due to its combination of cutting-edge technology and user-friendly design, making it suitable for a range of applications from data analysis to cloud computing.

One of the main features of the Fujitsu 2300 is its high-performance processing capabilities. Equipped with the latest generation of multi-core processors, it offers significant improvements in speed and efficiency. This ensures that users can handle demanding workloads without experiencing lag or downtime. Its architecture supports virtualization, allowing multiple operating systems to run simultaneously, which is essential for businesses that require flexibility and resource management.

In addition to processing power, the Fujitsu 2300 boasts advanced memory options. With support for large amounts of RAM, it caters to intensive tasks such as scientific simulations and large-scale databases. The ability to expand memory capacity means that the system can grow with the needs of the organization, ensuring longevity and adaptability in a rapidly evolving technological landscape.

Storage options on the Fujitsu 2300 are equally impressive. It offers a combination of traditional HDDs and high-speed SSDs, providing users with the flexibility to choose the configuration that best suits their needs. The inclusion of RAID technology enhances data protection and improves performance, making it ideal for environments where data integrity is paramount.

Connectivity features on the Fujitsu 2300 are tailored for modern network demands. With multiple USB ports, Ethernet options, and support for various communication protocols, it integrates seamlessly into existing IT infrastructures. This capability facilitates easy data sharing and connectivity with other devices.

Moreover, the Fujitsu 2300 incorporates advanced cooling technologies that maintain optimal operating temperatures, thereby increasing reliability and extending the lifespan of the hardware. Its build quality reflects Fujitsu’s commitment to durability and performance, ensuring that users benefit from a dependable computing solution over the long term.

Finally, the Fujitsu 2300 places emphasis on security, employing features such as hardware encryption and secure boot functionality. These characteristics are essential for organizations looking to protect sensitive information and comply with industry regulations.

In conclusion, the Fujitsu 2300 is a powerful and adaptable solution designed for today's demanding enterprise environments. With its high-performance processing, expandable memory, versatile storage options, advanced connectivity, robust cooling mechanisms, and strong security features, it represents a comprehensive computing solution for businesses aiming for efficiency and reliability.
Top Page Image Contents